INSTALLATION STEP 6

Install the Door Control

Locate door control within sight of the door at a minimum height of 5 feet where small children cannot reach, and away from moving parts of the door and door hardware. The installation surface must be smooth and flat. If installing into drywall (Figure 1), drill 5/32" holes and use anchors provided. For pre-wired installations (as in new home construction), it may be mounted to a single gang box (Figure 2). NOTE: After installation, a green or amber indicator light behind the cover will indicate proper connection. If not lit, the Lock and Light features will not function (reverse wires to correct).

1.Strip 7/16" of insulation from one end of bell wire and connect to the two screw terminals on back of door control by color: white wire to WHT and white/red wire to the RED (Figure 3).

2.Remove white cover by gently prying on a side corner near the top of the cover with a small flat head screwdriver (Figure 4). Fasten with 6ABx1-1/4" self-tapping screws (drywall installation) or 6-32x1" machine screws (into gang box) as follows:

ïDrill and install bottom screw, allowing 1/8" to protrude above wall surface.

ïPosition bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

ïInstall top screw with care to avoid cracking plastic housing. Do not overtighten.

ïInsert bottom tabs and snap on cover. (To remove cover after mounting, gently pry on a side corner near the top of the white cover with paper clip or small flat head screwdriver.)

NOTE: The push bar may stick if the door control is not mounted on a smooth surface. If a click is not heard when pressing the push bar, loosen the two mounting screws or relocate the door control to a smoother surface.

3. (Standard installation only) Run bell wire up wall

and across ceiling to motor unit. Use insulated

staples to secure wire in several places. Do not

pierce wire with a staple, creating a short or open

circuit.

4. Strip 7/16" of insulation from end of bell wire.

Connect bell wire to the quick-connect terminals as

follows: white to white and white/red to red (Figure 5).

WARNING

To prevent possible SERIOUS INJURY or DEATH from electrocution:

•Be sure power is not connected BEFORE installing door control.

•Connect ONLY to 24 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

•Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet, and away from all moving parts of door.

•NEVER permit children to operate or play with door control push buttons or remote control transmitters.

•Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

•ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.

HARDWARE SHOWN ACTUAL SIZE

Screw 6ABx1-1/4"

Insulated

(std installation)

Staples

Screw 6-32x1"

 

(pre-wired)

Drywall Anchors

STANDARD

PRE-WIRED

Figure 1 INSTALLATION

Figure 2 INSTALLATION

 

LOCK

 

 

LIGHT

 

LOCK

 

 

LIGHT

To Replace

24 Volt

To Replace

Insert Bottom Tabs First

2-Conductor

Insert Bottom Tabs First

 

Bell Wire in

 

 

 

 

Gang Box

Figure 3 MULTI-FUNCTION

Figure 4 REMOVE COVER

DOOR CONTROL (BACK)

 

Top Mounting Hole

 

 

Terminal

 

 

Screws

 

 

Bell Wire

 

LOCK

 

LIGHT

Bottom Mounting Hole

5. Use tacks or staples to permanently attach

entrapment warning label to wall near door control,

and manual release/safety reverse test label in a

prominent location on inside of garage door.

Figure 5

To release wire, push in tab with screwdriver tip

Door Control Connections

NOTE: DO NOT connect the power and operate the opener at this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned. See Safety Reversing Sensor Instructions beginning on page 17.

7/16"

Strip wire 7/16"

Red

White Grey

14