The following messages are contained within the Smart Control Panel™ and may appear during the operations of the unit:
Message | Meaning: This message will appear if the Safety Reversing Sensors are out of | ||
| SAFETY SENSORS | alignment, if they are blocked or if the wiring is disconnected. To clear message from | ||
| Smart Control Panel™ do the following: | |||
| CHECK | |||
• | Check to see that area is clear between the Safety Reversing Sensors. | ||
| ALIGNMENT, | |||
| BLOCKAGE OR | • | Check to see that the Safety Reversing Sensors are not misaligned. | |
| MISWIRING. SEE |
| • Realign receiving eye sensor, clean lens and secure brackets. | |
| OWNER’S MANUAL. |
| • Verify door track is firmly secured to wall and does not move. | |
| • Check to see that the Safety Reversing Sensors’ wires are connected to the motor unit. | ||
Message | • | If message has not cleared after the above checks, refer to message #2. | |
| Meaning: This message will appear if the Safety Reversing Sensors are miswired. | |||
SAFETY SENSORS | To clear the message, do the following: | ||
• Inspect the safety sensor wires for a short (staple in wire), correct wiring polarity (black/ | |||
| MALFUNCTION. | |||
| CHECK MISWIRING. |
| white wires reversed), replace/attach as needed. | |
| SEE OWNER’S | • | Disconnect all wires from back of motor unit. | |
| MANUAL. | |||
• | Remove safety sensors from brackets and shorten sensor wires to | ||
| |||
|
| from back of each sensor. | |
| • | Reattach sending eye to motor unit using shortened wires. If sending eye indicator light | |
|
| glows steadily, attach the receiving eye. | |
| • | Align sensors, if the indicator lights glow replace the wires for the sensors. If the sensor | |
Message |
| indicator lights do not light, replace the safety sensors. | |
| Meaning: This message will appear when the Prog <LEARN> button has been | |||
| LEARN REMOTE | pressed on the Smart Control Panel™. Pressing the Prog <LEARN> button again will | ||
| allow the user to program an additional remote control to the opener. | |||
| CONTROL. PRESS | |||
|
| ||
| LEARN BUTTON TO |
|
| |
| CONFIRM. |
|
| |
Message | Meaning: This message will appear when the Prog <learn> button has been pressed | ||
| LEARN MODE. | a second time on the Smart Control Panel™ or anytime on the opener. The opener is | ||
| ready to program another remote control by simply pressing the remote control | |||
| PRESS REMOTE | |||
button. Once the opener has ‘LEARNED’ the remote control, the worklight will blink | |||
| CONTROL BUTTON | |||
| one time. | |||
| TO PROGRAM | |||
|
| ||
| REMOTE. |
|
| |
Message | Meaning: This message will appear when the ‘Lock’ button has been pressed and | ||
| LOCK MODE. | |||
held for more than one second. This feature will disable the opener from receiving | |||
| REMOTE CONTROL | |||
remote control signals. To exit ‘LOCK’ mode, press and hold the button for more than | |||
| LOCKED OUT. | |||
| one second. | |||
| PRESS LOCK | |||
|
| ||
| BUTTON TO |
|
| |
| ENABLE REMOTE. |
|
| |
Message | Meaning: This message will appear when the ‘Language’ button has been pressed. | ||
| ENGLISH, | |||
| Pressing the button will toggle to the next language. | |||
| FRANÇAIS AND | |||
|
| ||
| ESPAÑOL. |
|
| |
Message | Meaning: This message will appear when the ‘MOTION SENSING’ button is pressed. | ||
| |||
| MOTION SENSING | The Motion Detector will toggle on or off with each press of the button. | ||
| ON, MOTION |
|
| |
| SENSING OFF. |
|
| |
|
| ||
32