Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 3585CS 3/4HP Install the Header Bracket, WALL HEADER BRACKET INSTALLATION, CEILING HEADER BRACKET INSTALLATION

1 80

Download 80 pages, 5.74 Mb

INSTALLATION STEP 2

Install the Header Bracket

You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided).

WALL HEADER BRACKET INSTALLATION

•Center the bracket on the vertical centerline with the bottom edge of the bracket on the horizontal line as shown (with the arrow pointing toward the ceiling).

•Mark the vertical set of bracket holes (do not use the holes designated for ceiling mount). Drill 3/16" pilot holes and fasten the bracket securely to a structural support with the hardware provided.

HARDWARE SHOWN ACTUAL SIZE

Wall Mounting Holes

CEILING MOUNT ONLY

UP

Optional

Wall Mounting Holes

Header
Wall	LY
Wall	MOUN
	T ON
	CEILING
	UP

2x4Header

Structural Bracket

Support

The nail hole is for positioning only.

You must use lag screws

to mount the header bracket.

Vertical

Centerline of

Garage Door

Lag Screws 5/16"-9x1-5/8"

Door Spring

Lag Screw 5/16"-9x1-5/8"

CEILING HEADER BRACKET INSTALLATION

•Extend the vertical centerline onto the ceiling as shown.

•Center the bracket on the vertical mark, no more than 6" (15 cm) from the wall. Make sure the arrow is pointing toward the wall. The bracket can be mounted flush against the ceiling when clearance is minimal.

•Mark the side holes. Drill 3/16" pilot holes and fasten bracket securely to a structural support with the hardware provided.

Ceiling Mounting Holes

CEILING MOUNT ONLY

UP

The nail hole is for positioning only.

You must use lag screws

to mount the header bracket.

Horizontal

Line

Garage

Door

Highest Point of

Garage Door TravelVertical

Centerline of

Garage Door

– Finished Ceiling –

		Vertical
	Header	Centerline
	Header	of Garage Door
	Bracket	of Garage Door
	Bracket
6" (15 cm)	UP
Maximum
Door		Lag Screws
Spring		Lag Screws
Spring		5/16"-9x1-5/8"
		5/16"-9x1-5/8"
		Header Wall
Garage Door	Vertical
	Vertical
	Centerline
	of Garage Door

9

Contents

GARAGE DOOR OPENER Model 3585CS 3/4HP Owner’s Manual TABLE OF CONTENTS Introduction Assembly Installation Adjustment Preparing your garage door Complete the following test Sectional Door One-PieceDoor Tools needed Planning SECTIONAL DOOR INSTALLATION ONE-PIECEDOOR WITHOUT TRACK ONE-PIECEDOOR WITH TRACK Carton Inventory INSTALLATION HARDWARE ASSEMBLY STEP Attach the Rail to the Motor Unit Set the Belt Tension IMPORTANT INSTALLATION INSTRUCTIONS WARNING To reduce the risk of SEVERE INJURY or DEATH: INSTALLATION STEP Determine the Header Bracket Location You can fasten the header bracket within 4 feet (1.22 m) of the left or right of the door center only if a torsion spring or center bearing plate is in the Install the Header Bracket WALL HEADER BRACKET INSTALLATION CEILING HEADER BRACKET INSTALLATION Attach the Rail to the Header Bracket Position the Opener SECTIONAL DOOR OR ONE-PIECEDOOR WITH TRACK Hang the Opener Install the Control Console CAUTION: SPECIAL NOTE: plastic housing. Do NOT overtighten 3. (For standard installations ONLY) Run bell wire up Install the Light Attach the Emergency Release Rope and Handle Electrical Requirements To avoid installation difficulties, do not run the opener at this time The opener must be grounded Install The Protector System® IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR Facing the door from inside the garage INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figure 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING SENSORS Fasten the Door Bracket SECTIONAL DOORS Metal, insulated or light weight factory reinforced doors: Wood Doors: Figure 2B ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley SECTIONAL DOORS ONLY Figure 1: • Figure 2: • Figure 3, Hole alignment alternative: ALL ONE-PIECEDOORS 1. Assemble the door arm, Figure 4: 2. Adjustment procedures, Figure 5: • Open door adjustment: decrease UP travel limit ADJUSTMENT STEP Adjust the UP and DOWN Travel Limits Run the opener through a complete travel cycle after each adjustment HOW AND WHEN TO ADJUST THE LIMITS •If the door does not open completely but opens at least 5 feet (1.5 m): Adjust the Force HOW AND WHEN TO ADJUST THE FORCES 1. Test the DOWN (close) force If the door is hard to hold or doesn’t reverse 2.Test the UP (open) force Test the Safety Reversal System TEST must ADJUST IMPORTANT SAFETY CHECK: IMPORTANT SAFETY INSTRUCTIONS Using the Wall-MountedControl Console THE LCD MOTION DETECTING CONTROL CONSOLE (PROG) Learn Feature (LANG) Language Feature Light feature Using the Remote Control Proximity Disable Feature To Control the Opener Lights Troubleshooting PROBLEM To Open the Door Manually MAINTENANCE SCHEDULE Once a Month Once a Year CARE OF YOUR OPENER HAVING A PROBLEM My door will not close and the light bulbs blink on my motor unit: 2.My remotes will not activate the door: My door reverses for no apparent reason: 5.My lights will not turn off when door is open: Diagnostic Chart 1 FLASH Symptom: One or both of the Indicator lights on the safety sensors do Safety reversing sensors not glow steady Smart Contol Panel™ Messages Meaning: This message will appear if the Safety Reversing Sensors are out of SAFETY SENSORS Smart Control Panel™ do the following: CHECK PROGRAMMING NOTICE: To Add or Reprogram a Hand-heldRemote Control USING THE “LEARN” BUTTON USING THE SMART CONTROL PANEL™ To Add, Reprogram or Change a Keyless Entry PIN USING THE SMART CONTOL PANEL™ To change an existing, known PIN To set a temporary PIN hours REPAIR PARTS Rail Assembly Parts Installation Parts KEY PART Motor Unit Assembly Parts ACCESSORIES Outside Quick Release: 373LMC 3-ButtonSecurity✚® Remote Control: Extension Brackets: Security✚® Keyless Entry: Page Page LIFTMASTER SERVICE IS HOW TO ORDER REPAIR PARTS ON CALL LIFTMASTER GARAGE DOOR OPENER FIVE-YEARLIMITED WARRANTY OUVRE-PORTEDE GARAGE Modèle 3585CS 3/4HP Manuel d’instructions TABLE DES MATIÈRES Introduction2-5 Montage Pose INTRODUCTION Préparation de votre porte de garage Outils nécessaires Planification Inventaire de la boîte d’emballage MONTAGE - 1re OPÉRATION Fixation du rail au moteur POSE IMPORTANTES INSTRUCTIONS CONCERNANT LA POSE Pour réduire le risque de BLESSURES GRAVES ou MORTELLES : POSE – 1re OPÉRATION Déterminer l’emplacement du support de linteau POSE – 2e OPÉRATION Pose du support de linteau POSE - 3e OPÉRATION Fixation du rail sur le support de linteau POSE - 4e OPÉRATION Positionnement de l’ouvre-porte POSE - 5e OPÉRATION Accrochage de l’ouvre-porte POSE - 6e OPÉRATION Pose de la console de commande POSE - 7e OPÉRATION Pose des l’ampoule POSE - 8e OPÉRATION Pose de la corde et de la poignée de déclenchement d’urgence POSE - 9e OPÉRATION Exigences électriques POSE - 10e OPÉRATION Pose du Système Protector® Page Page POSE - 11e OPÉRATION Fixation du support de porte Page POSE - 12e OPÉRATION Fixation de la biellette au chariot Page RÉGLAGES - 1re OPÉRATION Réglage des courses d’ouverture et de fermeture RÉGLAGES - 2e OPÉRATION Réglage de la force RÉGLAGES - 3e OPÉRATION Essai du système d’inversion de sécurité RÉGLAGES - 4e OPÉRATION Essai du Système Protector® FONCTIONNEMENT IMPORTANTES CONSIGNES DE SÉCURITÉ Pour réduire le risque de BLESSURES GRAVES ou de MORT : Utilisation de votre ouvre-portede garage Utilisation de la commande de porte à montage murale Utilisation de la Telecommande Ouverture manuelle de la porte ENTRETIEN DE L’OUVRE-PORTEDE GARAGE DÉFAUTS DE FONCTIONNEMENT Fiche Diagnostique 1 ÉCLAIR ÉCLAIRS ÉCLAIRS Page PROGRAMMATION Pour ajouter ou reprogrammer une télécommande à main supplémentaire Pour effacer tous les codes de la mémoire du moteur * Télécommandes à trois boutons Pour ajouter, reprogrammer ou modifier un NIP d’entrée sans clé PIÈCES DE RECHANGE Pièces d’assemblage du rail Pièces pour la pose Pièces d’assemblage du moteur ACCESSOIRES Page Page SERVICE LIFTMASTER À COMMENT COMMANDER DES PIÈCES DE RECHANGE VOTRE DISPOSITION GARANTIE LIMITÉE DE CINQ ANS SUR L'OUVRE-PORTEDE GARAGE LIFTMASTER