Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 3585S 3/4 HP Planning, ONE-PIECEDOOR WITH TRACK, ONE-PIECEDOOR WITHOUT TRACK

1 40

Download 40 pages, 4.35 Mb

Planning

Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may find it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener.

Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 19 for details.

Header Wall

FINISHED CEILING

Support bracket & fastening hardware is required.

See page 12.

	Extension	Motor Unit
	Extension
Torsion	Spring
Torsion	OR
Spring	OR
Spring

— — —

Vertical

Centerline

of Door

Access

Door

— — —

Wall- mounted Door Control

— —

Safety

Gap between floor and bottom Reversing Sensor

of door must not exceed 1/4" (6 mm)

Safety

Reversing Sensor

ONE-PIECE DOOR WITHOUT TRACK

FINISHED CEILING Support bracket

&fastening hardware is required. See page 12.

Motor Unit

Header

Wall

Wall- mounted

Door

Control Access Door

ONE-PIECE DOOR WITH TRACK

Safety

Reversing Sensor

	Gap between floor and bottom of
Safety	door must not exceed 1/4" (6 mm)

Reversing Sensor

Safety

Reversing Sensor

Access

Door

		Safety
	Gap between floor	Reversing
	Gap between floor	Sensor
	and bottom of door	Sensor
	and bottom of door
	must not exceed 1/4" (6 mm).

4

Contents

For Residential Use Only Introduction2-5 Assembly6-7 Installation7-22 Safety Symbol and Signal Word Review Adjustment23-25 Preparing your garage door Tools needed Planning Carton Inventory Attach the Rail to the Motor Unit Set the Belt Tension Attach the Belt Cap Retainer Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Light Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figure 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING ALIGNING THE SAFETY REVERSING SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1.Assemble the door arm, Figure 4: 2.Adjustment procedures, Figure 5: •Open door adjustment: decrease UP travel limit •Closed door adjustment: decrease DOWN travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control Using the Remote Control The Remote Control Battery Troubleshooting To Open the Door Manually HAVING A PROBLEM My door will not close and the light bulbs blink on my motor unit: 2.My remotes will not activate the door: My door reverses for no apparent reason: 5.My lights will not turn off when door is open: 1 FLASH 2 FLASHES 3 FLASHES 4 FLASHES 5 FLASHES Smart Control Panel™ Messages Message To Add or Reprogram a Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 1702LM Outside Quick Release: 41A5281 Extension Brackets: Page Page LIFTMASTER® GARAGE DOOR OPENER FIVE-YEARLIMITED WARRANTY LIFETIME MOTOR AND BELT LIMITED WARRANTY