Using the Remote Control

NOTE: To activate the remote control functions, pull out the plastic pull tab protruding from the remote control housing.

This remote control is equipped with a proximity lighting feature. When moving a hand within close proximity to the remote control, the LED lights turn on for 3 seconds. Upon successful activation of a remote control button, the LED lights will blink rapidly.

Proximity Disable Feature

The remote control will turn off the proximity lighting feature if the proximity lighting is turned on 10 consecutive times without activation of a button. To re-enable the proximity lighting, simply press a button. This function conserves battery life.

The Remote Control Battery

To prevent possible SERIOUS INJURY or DEATH:

•NEVER allow small children near batteries.

•If battery is swallowed, immediately notify doctor. To reduce risk of fire, explosion or chemical burn:

•Replace ONLY with 3V2016 or 3V2450 coin batteries.

•Do NOT recharge, disassemble, heat above 100°C (212°F) or incinerate.

The 3V2016 lithium batteries for the opener and LED lights (marked “LED and Opener Battery”) should last 5 years. The 3V2450 lithium battery for the proximity lighting (marked “Proximity Battery”) should last 1-2 years.

To Control the Opener Lights

With 315MHz Security✚® remote controls, a remote push button can be programmed to operate the opener lights without opening the door.

1.

With the door closed, press and hold the remote button

 

that you want to control the light.

2.

Press and hold the Light button on the

 

Smart Control PanelTM.

3.

Press and hold the Lock button on the

 

Smart Control PanelTM.

4.

After the opener lights flash, release all buttons.

To replace the batteries, remove the two screws and open the remote control housing. Push the battery out of the holder for removal. Insert replacement batteries positive side up. Dispose of old batteries properly.

Replace the batteries with only 3V2016 or 3V2450 coin cell batteries.

 

Proximity

 

Battery

LED and

Spring

Opener

Contact

Batteries

 

Test by pressing the remote push button. The opener lights should turn on or off but the door should not move.

Troubleshooting

 

PROBLEM

 

 

SOLUTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Check if proximity lighting is

 

 

 

 

 

disabled by pressing a button.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reduced proximity

 

 

The Proximity Sensor may be

 

sensing (does not

 

 

oversensitized. Sit remote control

 

 

activate by

 

 

undisturbed for 60 seconds on a

 

 

touching top of

 

 

non-metallic surface. This allows

 

 

remote control)

 

 

the sensor to recalibrate itself.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Replace 3V2450 battery with

 

 

 

 

 

same type 3V2450 coin cell.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Replace two 3V2016 batteries

 

Dim LED lights

 

 

 

with same type 3V2016 coin

 

 

 

 

 

 

cells.

 

 

 

 

 

 

 

No rapid LED

 

 

Replace two 3V2016 batteries

 

blinking after

 

 

with same type 3V2016 coin

 

pressing a button

 

 

cells.

 

 

 

 

 

 

 

 

 

 

CAUTION: Do not bend spring contact. If bent the proximity sensor will not work.

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

28