Manuals / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 8200 1/2 HP owner manual Attach the T-rail to the Header Bracket

Models: 8200 1/2 HP

1 40

Download 40 pages 7.64 Kb

Page 15

Image 15

Installation Step 3

Attach the T-rail to the Header Bracket

Header Wall

Header

Bracket

Belt Pulley

Bracket

T-rail

•Position the opener on the garage floor below the header bracket. Use packing material as a protective base.

If the door spring is in the way you'll need help. Have someone hold the opener securely on a temporary support to allow the T-rail to clear the spring.

•Position the belt pulley bracket against the header bracket.

•Align the bracket holes and join with a clevis pin as shown.

•Insert a ring fastener to secure.

Ring Fastener

Header Bracket

Clevis Pin

5/16"x2-3/4 "

Garage

Door

Belt Pulley Bracket

T-rail

Temporary

Support

Hardware Shown Actual Size

Clevis Pin
5/16"x2-3/4"	Ring Fastener

Page 15

Image 15

Chamberlain 8200 1/2 HP owner manual Attach the T-rail to the Header Bracket

Contents

Garage Door Opener Model 8200 Series Installation section pages 11 Start by reviewing these important safety alert symbolsContents Assembly section pages 8Youll Need Tools Closed Position Sectional Door InstallationONE-PIECE Door Installation One-Piece Door without TrackOne-Piece Door With Track Security Carton InventoryAssembly Right Wrong Assembly Section Pages 8Assembly Step Attach the Belt Pulley BracketFaster the T-rail to the Opener Install the Trolley on the T-railInstall the Belt & Set the Belt Tension Check to make sure the belt is not twistedDo not use any tools To attach the belt cap retainer Attach the Belt Cap RetainerProceed to , Installation Section Pages 12 Installation StepDetermine Header Bracket Location Sectional Door ONE-PIECE Door With Track=12 ExampleOne-piece door without track Jamb hardware One-piece door without track Pivot hardwareInstall the Header Bracket Fasten the Header Bracket to the WallFasten the Header Bracket to the Ceiling Attach the T-rail to the Header Bracket Position the Opener Sectional Door & ONE-PIECE Door with TrackRaise the opener onto a stepladder Trolley slides with rail grease Hang the OpenerGrease the top Underside of the rail Surface whereInstall the Multi-Function Door Control Panel Outside Keylock Accessory ConnectionsTo opener terminal screws white to 2 white/red to Reverse the procedure to remove the lenses Install the Lights and the Lenses32 explains how to use the door control See Safety Reversing Sensor Instructions beginning onElectrical Requirements Permanent Wiring ConnectionFacing the door from inside the garage Protector SystemInstall the Safety Reversing Sensor Mounting and Wiring the Safety Sensors Fasten Door Bracket Sectional Door Installation ProcedureHeader Wall Connect Door Arm to Trolley Sectional Doors OnlyHole Alignment Alternative All ONE-PIECE Doors Adjustment Procedures for One-Piece DoorsAdjustment Section Pages 28 Adjustment Step Adjust the UP and Down LimitsHow and When to Adjust the Limits Test the UP open force Adjust the ForceHow and When to Adjust the Forces Test the Down close forceTest the Safety Reverse System Important safety checkTest the Protector System Care of Your Opener Maintenance ScheduleLimit and Force Adjustment Controls Remote control batteryManual disconnect Position To open the door manually Operation of Your OpenerOperation of the Multi-Function Door Control Outside Keylock or Keyless EntryReceiver and Remote Control Programming Are the wiring connections correct? Review , Having a Problem?Situation Probable Cause & Solution Door control, a short under the staples, or a broken wireBulb if regular bulb burns out Is the Light feature on? Turn it offRepair Parts Rail Assembly PartsInstallation Parts Complete with Opener Assembly PartsAccessories Available for your Opener Index Chamberlain Service Is on Call