INSTALLATION STEP 7

Install the Door Control

Locate door control within sight of door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from moving parts of door and door hardware. The installation surface must be smooth and flat. If installing into drywall (Figure 1), drill 5/32" holes and use anchors provided. For pre-wired installations (as in new home construction), it may be mounted to a single gang box (Figure 2). NOTE: After installation, a green or amber indicator light behind the cover will indicate proper connection. If not lit, the Lock and Light features will not function (reverse wires to correct).

1.Strip 7/16" (11 mm) of insulation from one end of bell wire and connect to the two screw terminals on back of door control by color: white wire to WHT and white/red wire to the RED (Figure 3).

2.Remove cover by gently prying on a side corner near the top of the cover with a small flat head screwdriver (Figure 4). Fasten with 6ABx1-1/4" self- tapping screws (drywall installation) or 6-32x1" machine screws (into gang box) as follows:

•Drill and install bottom screw, allowing 1/8" (3 mm) to protrude above wall surface.

•Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

•Install top screw with care to avoid cracking plastic housing. Do not overtighten.

•Insert bottom tabs and snap on cover.

NOTE: The push bar may stick if the door control is not mounted on a smooth surface. If a click is not heard when pressing the push bar, loosen the two mounting screws or relocate the door control to a smoother surface.

3. (Standard installation only) Run bell wire up wall

and across ceiling to motor unit. Use insulated

staples to secure wire in several places. Do not

pierce wire with a staple, creating a short or open

circuit. If your access door is near the garage door,

you may run this wire with the Safety Reversing

Sensor wires along the top of the rail. See page 17.

WARNING

To prevent possible SERIOUS INJURY or DEATH from electrocution:

•Be sure power is not connected BEFORE installing door control.

•Connect ONLY to 24 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

•Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet

(1.52 m), and away from all moving parts of door.

•NEVER permit children to operate or play with door control push buttons or remote control transmitters.

•Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

•ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.

HARDWARE SHOWN ACTUAL SIZE

 

Screw 6ABx1-1/4"

 

Insulated

 

Control Panel (std installation)

Staples

 

Screw 6-32x1"

 

Drywall Anchors

 

Control Panel (pre-wired)

Figure 1

STANDARD

Figure 2

PRE-WIRED

INSTALLATION

INSTALLATION

LOCK

 

 

LIGHT

LOCK

 

To Replace

LIGHT

 

 

24 Volt

Insert Bottom Tabs First

To Replace

Bell Wire

 

Insert Bottom Tabs First

 

 

Figure 3

Figure 4

 

4. Insert all wires through the opening on top of motor

unit above the terminal block on the back panel

(Figure 4).

5. Strip 7/16" (11 mm) of insulation from each set of bell

wires. Connect bell wires to the quick-connect

terminals as follows: white to white and white/red to

red; white to white and white/black to grey (Figure 5).

NOTE: When connecting multiple door controls to the

opener, twist same color wires together. Insert wires

into quick-connect holes: white to white and red/white

to red.

MULTI-FUNCTION

WALL CONTROL PANEL

Terminal

Screws

Bell

Wire

RED WHT

1

2

Bottom

Mounting Hole

To release wire, push in tab with screwdriver tip

To

To Sensors

Door

Control

Quick-

Connect

Terminal

6. Use tacks or staples to permanently attach

entrapment warning label to wall near door control,

and manual release/safety reverse test label in a

prominent location on inside of garage door.

NOTE: DO NOT connect the power and operate the opener at this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned.

Door Control

Safety Sensor

Connections

Connections

Red White Grey

7/16" (11 mm)

Strip wire 7/16" (11 mm)

20