Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 9950 Rail Assembly Parts, Installation Parts, NO, NO, KEY, PART, DESCRIPTION, REPAIR PARTS

1 40

Download 40 pages, 1.75 Mb

REPAIR PARTS

	Rail Assembly Parts
			9
	1	10
	1	2			8
			7		8
	4		KEY	PART
			KEY	PART
			NO.	NO.	DESCRIPTION
	3		1	41A4796	Hardware bag
			2	41A4795	Hardware bag (includes
					sprocket coupling)
			3	12B569-1	Left rail bracket
			4	12B569-2	Right rail bracket
			5	1C4827-1	Screw drive rail assembly
			6	12B560	Rail support braces (4)
	5	6	7	81C168	Rack
	5		8	41C4677	Complete trolley assembly
			8	41C4677	Complete trolley assembly
			9	25C20	Sprocket coupling
			10	41A4836	Drive sprocket kit

Installation Parts

1 2 4 3

LOCK

LIGHT

		LY
	NT	ON
	OU
	G M
	LIN
7	CEI
	UP

6

5

9

NOTICE

10

8

11

12

13

KEY	PART
NO.	NO.	DESCRIPTION

1	41A5273-9	Multi-function door control
2	41A5056-3	Multi-function remote control case
		(no circuit board)
3	10A20	3V 2032 Lithium battery (1 required)
4	29B137	Visor clip
5	41A2828	Emergency release rope & handle assy.
6	217A238	2-Conductor bell wire: white & white/red
7	41A4353	Header bracket w/clevis pin & fastener
8	41A5047	Door bracket w/clevis pin & fastener
9	178B35	Curved door arm section
10	178B34	Straight door arm section
11	12B350	Hanging brackets
12	41A5034	Safety sensor kit: receiving and sending
		eyes with 3' 2-conductor bell wire
		attached
13	41A5266-1	Safety sensor bracket
		NOT SHOWN
	41A4675-7	Installation hardware bag (see page 7)
	114A2468	Owner's manual

37

Contents

For Residential Use Only Introduction Assembly Installation Adjustment Operation Preparing your garage door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail Assemble the Rail (Continued) Fasten the Rail to the Motor Unit and Install the Trolley Attach the Rail Brackets Determine the Header Bracket Location EXAMPLE One-piecedoor without track: jamb hardware One-piecedoor without track: pivot hardware Install the Header Bracket Attach the Rail to the Header Bracket Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Figure Wall installation: Floor installation: MOUNTING AND WIRING THE SAFETY SENSORS Recommended Wire Routing Do not use the lower (trolley) channels Position the Opener Hang the Opener Install the Door Control Install the Lights Attach the Emergency Release Rope and Handle Electrical Requirements Complete Safety Reversing Sensor Installation Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1.Assemble the door arm, Figure 4: 2.Adjustment procedures, Figure 5: •Open door adjustment: decrease UP travel limit •Closed door adjustment: decrease DOWN travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test the Protector System® Using Your Garage Door Opener Using the Wall-Mounted Door Control To Open the Door Manually Having a Problem Having a Problem? (Continued) To Add an Additional Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *Multi-FunctionRemotes To Add or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 950CB SECURITY✚ Single-Function 956CB SECURITY✚ Multi-FunctionMini www.chamberlain-diy.com CHAMBERLAIN GARAGE DOOR OPENER ONE-YEARLIMITED WARRANTY