INSTALLATION STEP 6
Install the Door Control
Locate door control within sight of door, at a minimum height of 5 feet (1.5 m) where small children cannot reach, away from moving parts of door and door hardware.
If installing into drywall, drill 5/32" holes and use the anchors provided. For
1.Strip 7/16" (11 mm) of insulation from one end of bell wire and connect to the two screw terminals on back of door control by color: white wire to 2 and white/red wire to the 1.
2.Remove cover by gently prying at slot in top of the cover with a small flat head screwdriver. Fasten with
•Install bottom screw, allowing 1/8" (3 mm) to protrude above wall surface.
•Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.
•Drill and install top screw with care to avoid cracking plastic housing. Do not overtighten.
•Insert top tabs and snap on cover.
3.(For standard installation only) Run bell wire up wall and across ceiling to motor unit. Use insulated staples to secure wire in several places. Do not pierce wire with a staple, creating a short or open circuit.
4.Strip 7/16" (11 mm) of insulation from end of bell wire. Connect bell wire to the
To prevent possible SERIOUS INJURY or DEATH from electrocution:
•Be sure power is not connected BEFORE installing door control.
•Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
•Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.
•NEVER permit children to operate or play with door control push buttons or remote control transmitters.
•Activate door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
•ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.
Outside Keylock Accessory Connections
To opener
HARDWARE SHOWN ACTUAL SIZE
| Screw | Insulated |
| Control Panel (std installation) | Staples |
| Screw | Drywall Anchors |
| Control Panel | |
Figure 1 | Figure 2 |
|
NOTE: When connecting multiple door controls |
|
| STANDARD WALL MOUNT |
|
| |||
|
| To Replace |
|
|
|
|
| |
to the opener, twist same color wires together. Insert |
| Insert Top |
| 24 Volt Bell Wire |
|
| ||
wires into |
| Tabs First |
| To Replace |
|
|
| |
|
| Insert Top |
|
|
| |||
|
|
|
|
|
| |||
red/white to red. |
|
|
|
| Tabs First |
|
|
|
|
|
|
|
|
|
|
| |
5. Use tacks or staples to permanently attach entrapment |
| ON |
|
|
|
| ||
| OFF |
|
|
|
| |||
warning label to wall near door control, and manual |
| LOCK | Detector |
|
|
|
| |
| LIGHT |
|
| Detector |
| |||
release/safety reverse test label in a prominent location | Push Bar Cover | Switch |
|
| ON | |||
|
| LOCK |
| Switch | OFF | |||
on inside of garage door. |
|
|
|
| Push Bar Cover | LIGHT |
|
|
|
|
|
|
|
|
|
| |
NOTE: DO NOT connect power |
|
|
|
|
|
|
| |
and operate opener at this time. |
|
|
| Terminals |
|
|
| |
|
|
|
|
|
|
| ||
The trolley will travel to the full |
|
|
|
|
|
|
| |
|
|
| Bell Wire |
|
|
|
| |
open position but will not return |
| Top |
|
|
|
|
|
|
to the close position until the |
| Mounting |
|
|
|
|
| |
sensor beam is connected and |
| Hole |
|
|
|
|
|
|
WHITE | Terminal | Push |
|
|
|
| ||
properly aligned. |
|
|
|
| ||||
2 | Bar |
|
|
|
| |||
| Screws |
|
|
|
| |||
|
|
|
|
|
|
| ||
Bell | RED | Bottom |
|
|
|
|
|
|
1 |
|
|
|
|
|
| ||
Wire |
| Mounting | Lock |
|
|
|
| |
|
| Hole |
|
|
|
|
| |
|
|
|
|
|
|
|
|
(BACK VIEW)
LOCK
LIGHT
Light
Door Control | To release wire, push in | |
Connections | tab with screwdriver tip | |
7/16" (11 mm) |
|
|
Strip wire 7/16" (11 mm) Red | White | Grey |
17