Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain HD800D Hardware Inventory, ASSEMBLY HARDWARE, INSTALLATION HARDWARE

1 44

Download 44 pages, 2.73 Mb

Hardware Inventory

Separate all hardware and group as shown below for the assembly and installation procedures.

ASSEMBLY HARDWARE

Spring/Trolley Nut (1)	Lock Nut	Lock Washer	Nut
Spring/Trolley Nut (1)	1/4"-20 (2)	3/8" (1)	3/8" (1)

Bolt 1/4"-20x1-3/4" (2)

Master
Link (2)	Idler Bolt (1)

Trolley Threaded Shaft (1)

INSTALLATION HARDWARE

Carriage Bolt

Wing Nut

Ring

Nut 5/16"-18 (8)

Handle

1/4"-20x1/2" (2)

1/4"-20 (2)

Fastener (3)

Lag Screw	Hex Bolt		Insulated
5/16"-9x1-5/8" (2)	5/16"-18x7/8" (4)	Lock Washer 5/16" (7)	Staples (30)

Lag Screw	Screw	Screw 6-32x1" (2)
5/16"-18x1-7/8" (2)	6ABx1-1/4" (2)	Screw 6-32x1" (2)

Rope

Self-Threading Screw		Spacer (2)
1/4"-14x5/8" (2)	Drywall Anchors (2)

Clevis Pin	Clevis Pin	Clevis Pin
5/16"x1-1/2" (1)	5/16"x1" (1)	5/16"x1-1/4" (1)

Contents

For Residential Use Only Introduction Assembly Installation Adjustment Operation Preparing your garage door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Belt and Attach the Belt Cap Retainer Set the Tension Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Lights Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figure 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1.Assemble the Door Arm: Program the Travel Limits Setting the Force Test the Safety Reversal System Test The Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually BATTERY BACKUP UNIT 1. Mounting the BBU Directly to the Motor Unit 2.Mounting the BBU Directly to the Ceiling Structural Support 3. Connect the BBU to the Motor Unit IMPORTANT NOTE: OPERATING INSTRUCTIONS 1. Test the installed BBU with the motor unit 2. Charge the battery Battery Backup Unit (BBU) Diagnostics GREEN LED: CARE OF YOUR OPENER MAINTENANCE SCHEDULE Once a Month THE REMOTE CONTROL BATTERY Once a Year HAVING A PROBLEM The opener doesn't operate from either the Door Control or the remote control: 2.Opener operates from the remote, but not from the Door Control: 3.The door operates from the Door Control, but not from the remote control: 4. The remote control has short range: 1 FLASH 2 FLASHES 3 FLASHES 4 FLASHES 5 FLASHES To Add or Reprogram a Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 953D 3-ButtonSECURITY✚® Remote 7702CB Control: Page Page CHAMBERLAIN® THREE YEAR LIMITED WARRANTY 10 YEAR BELT LIMITED WARRANTY & LIFETIME MOTOR LIMITED WARRANTY