Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain WD822KS Planning (Continued), ONE-PIECEDOOR INSTALLATIONS, ONE-PIECEDOOR WITHOUT TRACK

1 40

Download 40 pages, 4.33 Mb

Access Door

Safety

Reversing Sensor

Planning (Continued)

ONE-PIECE DOOR INSTALLATIONS

•Generally, a one-piece door does not require reinforcement. If your door is lightweight, refer to the information relating to sectional doors in Installation Step 11.

•Depending on your door’s construction, you may need additional mounting hardware for the door bracket (Step 11).

ONE-PIECE DOOR WITHOUT TRACK
	FINISHED CEILING
	Support bracket
	& fastening
	hardware is required.
	See page 16.
Header Wall	Rail
Header Wall
		Motor Unit
	Wall-mounted
	Door Control
	Access		CLOSED POSITION
	Door		CLOSED POSITION
	Door
				Trolley
		Header
		Bracket
		Door Bracket		Emergency
	Safety Reversing			Release
Gap between floor	Sensor			Rope & Handle
Gap between floor			Straight	Curved
and bottom of door must not exceed 1/4" (6 mm).			Straight	Door
and bottom of door must not exceed 1/4" (6 mm).			Door	Door
Safety Reversing Sensor			Door	Arm
			Arm	Arm
	Header		Arm
	Header	Garage
	Wall	Garage
	Wall	Door
		Door

Safety

Reversing Sensor

Header

Wall

Gap between floor and bottom of door

must not exceed 1/4" (6 mm).

CLOSED POSITION

	Trolley Stop Bolt		Belt	Trolley
	Header	Curved
	Bracket	Door Arm		Rail
	Door			Emergency
	Bracket		Straight	Release
	Garage		Door	Rope &
			Door	Handle
			Arm	Handle
	Door		Arm
	Door

5

Contents

For Residential Use Only Introduction Assembly Adjustment Operation Installation11-26 Preparing your garage door Tools needed Planning Planning (Continued) Page Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Belt and Attach the Belt Cap Retainer Set the Tension Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Lights Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® Page MOUNTING AND WIRING THE SAFETY REVERSING SENSORS ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1.Assemble the door arm, Figure 4: 2.Adjustment procedures, Figure 5: •Open door adjustment: decrease UP travel limit •Closed door adjustment: decrease DOWN travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: Repeat the safety reverse test (Adjustment Step 3, page 29) after any adjustment of limits or force MAINTENANCE SCHEDULE HAVING A PROBLEM 1. My door will not close and the light bulbs blink on my motor unit: 2. My remotes will not activate the door: 3. My door reverses for no apparent reason: Page To Add or Reprogram a Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 950CB 1-ButtonSECURITY✚® Remote 7702CB Outside Quick Release: CHAMBERLAIN® ONE-YEARLIMITED WARRANTY 10 YEAR BELT LIMITED WARRANTY & LIFETIME MOTOR LIMITED WARRANTY