Chamberlain WD952KD, WD952LD Install the Door Control, NOTE:, NOTE:, Figure, Figure, Do not overtighten, Outside Keylock Accessory Connections

INSTALLATION STEP 6					WARNING
Install the Door Control		To prevent possible SERIOUS INJURY or DEATH from
Locate door control within sight of door, at a		electrocution:
		• Be sure power is not connected BEFORE installing door
minimum height of 5 feet (1.5 m) where small
		control.
children cannot reach, away from moving parts of
		• Connect ONLY to 24 VOLT low voltage wires.
door and door hardware. If installing into drywall, drill
		To prevent possible SERIOUS INJURY or DEATH from a
5/32" holes and use the anchors provided. For
pre-wired installations (as in new home construction),		closing garage door:
		• Install door control within sight of garage door, out of
it may be mounted to a single gang box (Figure 2).
1. Strip 7/16" (11 mm) of insulation from one end of		reach of children at a minimum height of 5 feet
		(1.5 m), and away from all moving parts of door.
bell wire and connect to the two screw terminals
		• NEVER permit children to operate or play with door
on back of door control by color: white wire to
		control push buttons or remote control transmitters.
2 and white/red wire to the 1.
		• Activate door ONLY when it can be seen clearly, is
2. Remove cover by gently prying at slot in top of the
		properly adjusted, and there are no obstructions to door
cover with a small flat head screwdriver. Fasten
		travel.
with 6ABx1-1/4" self-tapping screws (drywall
		• ALWAYS keep garage door in sight until completely
installation) or 6-32x1" machine screws (into gang
		closed. NEVER permit anyone to cross path of closing
box) as follows:
		garage door.
• Install bottom screw, allowing 1/8" (3 mm) to
protrude above wall surface.			Outside Keylock Accessory Connections
• Position bottom of door control on screw head		To opener quick-connect terminals: white to white;
and slide down to secure. Adjust screw for		white/red to red.
snug fit.
• Drill and install top screw with care to avoid				HARDWARE SHOWN ACTUAL SIZE
cracking plastic housing. Do not overtighten.
• Insert top tabs and snap on cover.				Screw 6ABx1-1/4"			Insulated
3. (For standard installation only) Run bell wire up				Control Panel (std installation)			Staples
wall and across ceiling to motor unit. Use insulated
staples to secure wire in several places. Do not				Screw 6-32x1"		Drywall Anchors
pierce wire with a staple, creating a short or open				Control Panel (pre-wired)
circuit.	Figure 1				Figure 2
4. Strip 7/16" (11 mm) of insulation from end of
	STANDARD WALL MOUNT				PRE-WIRED INSTALLATION
bell wire. Connect bell wire to the
	To Replace				24 Volt Bell Wire
quick-connect terminals as follows: white to	Insert Top
	Tabs First				To Replace
white and white/red to red.					Insert Top
NOTE: When connecting multiple door					Tabs First
controls to the opener, twist same color wires		LOCK		Detector	ON
together. Insert wires into quick-connect holes:
	Push Bar Cover		L		OFF
			IGHT	Switch			Detector
								ON
white to white and red/white to red.						LOCK	Switch	OFF
					Push Bar Cover	LIGHT

5.Use tacks or staples to permanently attach entrapment warning label to wall near door control, and manual release/safety reverse test label in a prominent location on inside of garage door.

NOTE: DO NOT connect power and operate opener at this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned.

					Quick-Connect
			2-Conductor		Terminals
			Bell Wire
		Top
		Mounting
		Hole
	WHITE	Terminal		Push
	2			Bar
		Screws
Bell	RED	Bottom
	1
Wire		Mounting		Lock
		Hole
	(BACK VIEW)		LIG	Light
		K
		L
		OC
			HT
			Door Control	To release wire, push in
			Connections	tab with screwdriver tip
		7/16" (11 mm)
		Strip wire 7/16" (11 mm) Red			White	Grey

17