INSTALLATION STEP 6

Install the Door Control

Locate door control within sight of door, at a minimum height of 5 feet (1.5 m) where small children cannot reach, away from moving parts of door and door hardware.

If installing into drywall, drill 5/32" holes and use the anchors provided. For pre-wired installations (as in new home construction), it may be mounted to a single gang box (Figure 2).

1. Strip 7/16" (11 mm) of insulation from one end of bell

wire and connect to the two screw terminals on back of

the door control by color: white wire to 2 and white/red

wire to the 1.

2. Remove cover by gently prying at slot in top of the cover

with a small flat head screwdriver. Fasten with

6ABx1-1/4" self-tapping screws (drywall installation) or

6-32x1" machine screws (into gang box) as follows:

• Install bottom screw, allowing 1/8" (3 mm) to protrude

above wall surface.

• Position bottom of the door control on screw head and

slide down to secure. Adjust screw for snug fit.

• Drill and install top screw with care to avoid cracking

plastic housing. DO NOT overtighten.

• Insert top tabs and snap on cover.

3. (For standard installation only) Run bell wire up wall

and across ceiling to motor unit. Use insulated staples

to secure wire in several places. DO NOT pierce wire

with a staple, creating a short or open circuit.

4. Strip 7/16" (11 mm) of insulation from end of bell wire.

Connect bell wire to the quick-connect terminals as

follows: white to white and white/red to red.

5. Position the antenna wire as shown.

To prevent possible SERIOUS INJURY or DEATH from electrocution:

•Disconnect ALL electric and battery power BEFORE performing ANY service or maintenance.

•Connect ONLY to 24 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

•Install the door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.

•NEVER permit children to operate or play with the door control push buttons or remote controls.

•Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

•ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.

Outside Keylock Accessory Connections

To opener quick-connect terminals: white to white; white/red to red.

HARDWARE SHOWN ACTUAL SIZE

Screw 6ABx1-1/4"

Insulated

(standard installation)

Staples

Screw 6-32x1"

 

(pre-wired)

Drywall Anchors

Figure 1

Figure 2

6. Use tacks or staples to permanently attach entrapment

warning label to wall near door control, and manual

release/safety reverse test label in a prominent location

on inside of garage door.

NOTE: DO NOT connect power and operate opener at this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned.

STANDARD WALL MOUNT

To Replace

Insert Top

Tabs First

 

 

ON

 

 

OFF

K

 

 

LOC

 

 

 

LIGH

T

Push Bar Cover

Detector

 

 

 

Switch

PRE-WIRED INSTALLATION

24 Volt Bell Wire

To Replace

Insert Top

Tabs First

K

Detector

ON

Switch

OFF

LOC

LIGHT

Push Bar Cover

 

Top

 

Mounting

 

Hole

WHITE

Terminal

2

 

Screws

RED

Bottom

1

Bell

Mounting

Wire

Hole

(BACK VIEW)

 

Door Control Connections

Strip wire 7/16" (11 mm)

7/16" (11 mm)

To insert or release wire, push in tab with screwdriver tip

Red White Grey

17