![MAINTENANCE](/images/new-backgrounds/43701/437017x1.webp)
OPTIONAL ACCESSORIES
Chart A – Kit Selection Guide
Model | Grill | Disconnect | Hanger | Wall Mount | Portable | |
Kit | Kit | Kit | Ground Fault | Cart Kit** | ||
| ||||||
PCN 111878 |
|
| NA | NA | ||
|
|
|
|
|
| |
PCN 111878 |
|
| PCN 340777 | NA | ||
|
|
|
|
|
| |
PCN 111878 |
|
| PCN 340785 | NA | ||
|
|
|
|
|
| |
PCN 111878 |
|
| PCN 340793 | NA | ||
|
|
|
|
|
| |
PCN 111878 |
|
| PCN 340806 | NA | ||
|
|
|
|
|
| |
PCN 111878 |
|
| PCN 340814 | NA | ||
|
|
|
|
|
| |
PCN 111894 |
|
| PCN 340777 | PCN 340620 | ||
|
|
|
|
|
| |
PCN 111894 |
|
| PCN 340785 | PCN 340620 | ||
|
|
|
|
|
| |
PCN 111894 |
|
| PCN 340793 | PCN 340620 | ||
|
|
|
|
|
| |
PCN 111894 |
|
| PCN 340806 | PCN 340620 | ||
|
|
|
|
|
| |
PCN 111894 | PCN 340662 | PCN 340654 | PCN 340814 | PCN 340620 | ||
|
|
|
|
|
| |
PCN 340638 |
|
| PCN 340777 | PCN 340830 | ||
PCN 340638 |
|
| PCN 340785 | PCN 340830 | ||
|
|
|
|
|
| |
PCN 340638 |
|
| PCN 340793 | PCN 340830 | ||
|
|
|
|
|
| |
PCN 340638 |
|
| PCN 340806 | PCN 340830 | ||
|
|
|
|
|
| |
PCN 340638 |
|
| PCN 340814 | PCN 340830 | ||
|
|
|
|
|
| |
PCN 340857 |
|
| PCN 340777 | PCN 340849 | ||
|
|
|
|
|
| |
PCN 340857 |
|
| PCN 340785 | PCN 340849 | ||
|
|
|
|
|
| |
PCN 340857 |
|
| PCN 340793 | PCN 340849 | ||
|
|
|
|
|
| |
PCN 340857 |
|
| PCN 340806 | PCN 340849 | ||
|
|
|
|
|
| |
PCN 340857 |
|
| PCN 340814 | PCN 340849 | ||
|
| |||||
|
|
|
|
|
|
** Includes Grill(s)
MAINTENANCE
ELECRIC SHOCK HAZARD. Disconnect all power before servicing or replacing heating elements.
BURN HAZARD. Hot surfaces. Allow sufficient time for heater to cool before serviceing or cleaning heater.
The reflectors should be kept clean to obtain the maximum radiant output.
Element Replacement
1.Remove Terminal Box Cover.
2.Disconnect lead wires from heater terminals and disengage box from conduit /cable fitting.
3.Remove safety grills (if installed).
4.Remove retainer screw located on the reflector at the terminal end.
5.Loosen (2), 3/8" nuts from the terminal box bracket located on the back of the heater and slide the entire heating element assembly out of the reflector assembly.
6.Remove wires and jumper straps as required to replace the failed heating element(s).
7.Remove bulkhead fitting nuts and washers.
8.Remove failed element and replace with a new element. Replace only with genuine Chromalox "Arctic End" elements. Use of other elements will cause excess temperatures inside terminal box.
9.Place gasket on the bulkhead fitting and insert terminals and fit- tings into the element holes in the terminal box.
10.Place washers and nuts on bulkhead fittings and tighten.
11.Replace wiring and jumper straps (see Fig. 1).
12.Reassemble by following the reverse procedures (steps 5 through 1).
4