Cisco Systems 1500 - page 9

1-9

Cisco Metro 1500 Series Hardware Installation Guide

78-10588-03

Chapter1 Product Overview Communication Channels

Figure 1-7 Rear View of the Chassis

Each chassis is deliveredwith one to eight WCMs, according to the configuration

ordered. Each WCM provides the conversion of the local or remote channels to

their respective wavelengths.All modules are hot-swappable and can be repaired

orupgraded while the other WCMs are in use. WCMs support a wide range of data

rates. For more information on data rates, optical budgets, and supported

protocols,see Appendix A, “Specifications,” and Appendix E, “Unit Maintenance

and Network Record.”

The RSM is available as an option. The RSM provides the system with 1+1 line

protection and is installed in the primary chassis only. (See Figure 1-3).

The primary chassis and extension chassis B also include the network element

management interface (NEMI) module. Extension chassis A and C includes an

optional device element management interface (DEMI) module. For information

on the NEMI and DEMI, refer to the Cisco Metro 1500 Series Software

Configuration Guide.

Certification

marks

Identification

plate

Instructions for

power supply

Fan module

AC power

connectors Fuse

holders

39353

FSP - II/1/WDM

Manufactured:March 2000

Model:

BASE-F2Z-D2-A1-ZZ

Serial-No.:

AD-23-W349

ADVA AG, 98617 Meiningen, Jerusalemer Straße 13, Germany

Only valid if all modules and/or blind panels are in place

.

Voltage:

Max. Current:

Power Consumption:

Fuse:

For continued protection against risk of fire replace

only with same type and ratings of fuse.

For proper selection of power supply cord refer to

instruction manual.

Made in Germany

March 1998

Always remove both

power cords when dis-

connecting from power

source 1.

!

115/230 V 50/60 Hz

2.5 A

max. 100W

2x T2.5A / 250V

Fuse 1

Fuse 2 Power 1Power 2

Contents

Main CHAPTER Product Overview Product Description Communication Channels Figure 1-1 shows the multiplexer architecture. Figure 1-1 Multiplexer Architecture Primary and Extension Chassis Cisco Metro 1500 Series Hardware Installation Guide 78-10588-03 Chapter1 Product Overview Communication Channels Figure 1-2 Typical Cisco Metro1500 Series Conguration Ethernet cables Ethernet hub DC Input Uplink 6x 5x 4x 3x 2x 1x External bus cable Expansion Modules Power 1 Power 2 WCM RSM Figure 1-3 Primary Chassis NEMI DMX Figure 1-4 Extension Chassis A Figure 1-5 Extension Chassis B WCM BSM DMX Power 1 Power 2 Figure 1-7 shows the rear view of the primary chassis and extension chassis. 78-10588-03 Figure 1-6 Extension Chassis C WCM MUX DMX Power 1 Power 2 Page 16-Channel WCM System 32-Channel WCM System 128-Channel ESCON System Chassis Dimensions Labeling Page Airflow System Power Supply Module System Modules Wavelength Channel Modules Data Rate Transparent WCMs Data Rate Transparent Front Panel LEDs WCMs with Fixed Clock Recovery Clock Recovery Front Panel LEDs WCMs with Settable Clock Recovery Optical Connectors of the WCM Multiplexer and Demultiplexer Modules Chapter1 Product Overview System Modules Figure 1-10 MUX and DMX Locations Optical Connectors of the MUX and DMX Each MUX and DMX has up to 10 optical connectors: One input or output connector for each of up to eight WCMs installed in a chassis. One common input (D1 to D4 WCM chassis location), depending on the Band Splitter Module Optical Connectors of the BSM Remote Switch Module Page Figure 1-13 RSM Optical Connectors RSM Push Buttons and LEDs Three push buttons control the RSM. Table1-5 lists each push button and its function. Table1-5 RSM Push Button Descriptions Optical Connectors of the RSM Modes of Operation TDM4E Wavelength Channel Modules Page Page System Modules Figure 1-15 TDM4E Multiplexer Architecture RSM DMX TDM4E1 TDM4E2 Optical Connectors of the TDM4E On the front panel of the TDM4E there are 10 MiniSC type optical connectors: Figure 1-16 shows the optical connectors on the front panel of the TDM4E. Figure 1-16 Optical Connectors of the TDM4E TDM4E LEDs Page Network Element Management Interface Chapter1 Product Overview System Modules NEMI Location Placement POWER FAN Ch.1-8 32262 Figure 1-17 NEMI Location in the Primary Chassis and Extension Chassis B Figure 1-18 NEMI Front Panel NEMI LEDs Device Element Management Interface System Modules METRO 1500 POWER FAN DEMI Location Placement The physical location of the DEMI module is shown in Figure 1-19. Figure 1-19 DEMI Placement in an Extension Chassis DEMI Ports MUX Ch.9-16 DMX DEMI LEDs Ethernet Hub