Cisco Systems 1760 - page 51

2-9

Cisco 1760 Modular Access Router Hardware Installation Guide

78-13342-03

Chapter2 Installation

Installing WICs and VICs

Warning

Before opening the chassis, disconnect the telephone-network cables (from the

card) to avoid contact with the telephone-network voltages.

Warning

Do not work on the system or connect or disconnect cables during periods of

lightning activity.

Caution Do not connect a WAN, telephone, or fax cable to the card until you have

completed the installation procedure.

Follow these steps to remove or insert a card in the router:

Step1 Make sure that the router is turned off and is disconnected from power.

Caution Power must be disconnected from the system before installing or removing WICs

or VICs to avoid damaging them. When WICs or VICs are pushed into or pulled

out of a router that is powered up, there is a very good chance that they could be

damaged electrically and will no longer function.

Step2 Loosen the thumbscrews on the WIC or VIC slot cover, as shown in Figure 2-6.

Figure2-6 Removing a WIC or VIC Slot Cover

You should be able to loosen the screws using your fingers; however, if the screws

are very tight, you might need to use a Phillips screwdriver.

60950

Cisco 1700

Series

10/100 ETHERNETAUX

CONSOLE

PVDM 0

OK

OK

PWR 1

0

SLOT 0

OK

PVDM 1

OK

MOD

OK

1

0

SLOT 1

OK

LINK

100

FDX

ACT COL 1

0

SLOT 2

OK

1

0

SLOT 3

OK

Contents

Main Page Page Page CONTENTS Page Page Page Preface Audience and Scope Organization Related Documentation Conventions Notes, Cautions, and Warnings xiv Warning Definition xv xvi xvii xviii xix Page Page Commands Obtaining Documentation Cisco.com Documentation DVD Ordering Documentation Documentation Feedback Cisco Product Security Overview Reporting Security Problems in Cisco Products Obtaining Technical Assistance Cisco Technical Support Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Page Page 1-1 Cisco 1760 Router Overview Key Features Ports and LEDs Router Memory Unpacking the Router Additional Required Equipment Figure 1-1 shows the Cisco1760 router. Figure1-1 Cisco1760 Router Key Features Ports and LEDs 1 2 3 16 15 13 9 814 12 11 7 6 10 4 5 Ports System LEDs Ethernet LEDs WIC/VIC LEDs Page Page Router Memory Types of Memory Amounts of Memory Unpacking the Router Additional Required Equipment Page Page Installation Before Installing the Router Mounting the Router in a Rack Attaching Brackets to the Router Mounting the Router in a Rack 2-4 Figure2-2 Attaching Brackets for 19- and 24-Inch Racks Phillips flat-head screws 19" Configuration Phillips truss-head screws Attaching Brackets to the Rack Attaching the Optional Cable Guide Cisco 1700 Series Connecting the Router to Your Local Network Connecting the Router to Your Local Network A straight-through, RJ-45-to-RJ-45 Ethernet cable A 10/100-Mbps Ethernet hub or switch Warning Caution Always connect the Ethernet cable to the yellow ports on the router. Do not Cisco 1700 Series 2-7 Connecting the Router to Your Local Network Step2 Connect the other end of the cable to a network port on the hub or switch. Follow these steps to connect the router to your local network: Step1 Connect one end of the cable to the yellow Ethernet port (labeled 10/100-Mbps Installing WICs and VICs Safety Information Page 1 2 Connecting Power to the Router Verifying the Installation Optional Installation Steps Connecting a PC Connecting a Modem 2-15 Optional Installation Steps Figure2-10 Connecting a Modem to the Router 1Aux port (RJ-45) 3DB-9-to-DB-25 adapter 2Modem 4Console cable Cisco 1700 Page Troubleshooting Contacting Your Cisco Reseller Recovering a Lost Password Determining the Configuration Register Value 3-3 Step4 At the user EXEC prompt (Router>), enter the show version command to Step5 Record the setting of the configuration register. It is usually 0x0. display the existing configuration register value (shown at the end of this example output): Resetting the Router Page Resetting the Password Resetting the Configuration Register Value Problem-Solving OK LED Diagnostics Troubleshooting WICs and VICs 3-9 3-10 Page Troubleshooting the Power System Troubleshooting ISDN Page Fan Behavior Page A Technical Specifications Page B Cabling Specifications Ethernet Cables Ethernet Network Cabling Guidelines Console Cable and Adapter VIC Cables and Pinouts Page Cables and Pinouts for 2-Port ISDN BRI Card Page C Installing and Upgrading Memory and Packet Voice Data Modules Safety Information C-2 Opening the Chassis AppendixC Installing and Upgrading Memory and Packet Voice Data Modules Locating Modules C-4 Step4 Place the router bottom on an antistatic mat, and begin installing modules. VIC-only slots Locating Modules FigureC-3 Cisco 1760 MotherboardModule Locations Installing a DIMM DIMM slot SIMM slot VPN module Power supply PVDM slot 1 PVDM slot 0 Page Installing a SIMM Installing a PVDM Vi ew id f Page Page Closing the Chassis D Installing the Virtual Private Network Module Before You Begin VPN Module Parts D-2 Safety Warnings Preventing Electrostatic Discharge Damage Installing the VPN Module in a Cisco 1760 Router Opening the Cisco 1760 Chassis D-5 Chassis screw Pull the top cover off in this direction. Installing the VPN Module D-7 Step2 Locate the VPN module socket, and insert the VPN module, as shown in Figure D-4. FigureD-4 VPN Module Location Standoffs Page Closing the Cisco 1760 Chassis Page E Installing the Echo Canceler Expansion Modules on Cisco Interface Cards Multiflex Trunk Interface Cards Echo Echo Canceler Expansion Modules Installing and Configuring the Echo Canceler Expansion Modules Page INDEX A B C D E F I L M N O P R S T U V W