Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems PAP2 manual Wall-Mount Option, Measurement between Wall-Mount Slots

Models: PAP2

1 46

Download 46 pages 25.12 Kb

Page 14

Phone Adapter with 2 Ports for Voice-over-IP

Wall-Mount Option

The Phone Adapter has two wall-mount slots on its back panel. The distance between the two slots is 58 mm (2.28 inches).

1.Determine where you want to mount the Phone Adapter.

2.Drill two holes into the wall. Make sure the holes are 58 mm (2.28 inches) apart.

3.Insert a screw into each hole, and leave 5 mm (0.2 inches) of its head exposed.

4.Maneuver the Phone Adapter so the wall-mount slots line up with the two screws.

5.Place the wall-mount slots over the screws and slide the Phone Adapter down until the screws fit snugly into the wall-mount slots.

Congratulations! The installation of the Phone Adapter is complete.

If you need to change any of the Phone Adapter’s network settings, proceed to “Chapter 4: Using the

Phone Adapter’s Interactive Voice Response Menu.”

8

Figure 3-7: Measurement between

Wall-Mount Slots

Chapter 3: Connecting the Phone Adapter Placement Options

Image 14

Cisco Systems PAP2 manual Wall-Mount Option, Measurement between Wall-Mount Slots

Contents

Phone Adapter Page How to Use this Guide Copyright and TrademarksPhone Adapter with 2 Ports for Voice-over-IP Table of Contents Back Panel Front PanelWhat’s in this Guide? IntroductionWelcome Introduction Getting to Know the Phone Adapter Back Panel PortsIncoming call has been detected Front PanelPhone Adapter’s LEDs are located on the front panel An incoming call has been detectedOverview Connecting the Phone AdapterInstructions for Connecting the Phone Adapter InternetFollow the instructions provided by Vonage Connect the Telephone CableRemove the plate from the Phone Adapter’s bottom panel Placement OptionsStand Option Phone Adapter’s Interactive Voice Response MenuWall-Mount Option Measurement between Wall-Mount SlotsUsing the Interactive Voice Response Menu Using the Phone Adapter’s Interactive Voice Response MenuAccessing the Interactive Voice Response Menu Not press any other keys until you Use this command to enter Response MenuInteractive Voice Response Menu Key or hang up to exitEnter 0 to disable Has been enabled or disabled. If101 Enter 1 to enable Check Dhcp 100Subnet Mask Mask using Address usingStatic IP address When entering a Decimal point Network mask When entering a Decimal pointPhone Adapter Manual Reboot 732668 Address Address usingStatic gateway IP address When entering a Decimal point 131 Enter the IPConfiguring the Settings for Your Internet Phone Service Appendix a Troubleshooting Common Problems and SolutionsAppendix a Troubleshooting IP address Phone Adapter Internet phone 53 to Application Start and End Protocol IP Address EnableInternet phone 5060 to IP address Phone Adapter Internet phone 69 toPhone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Frequently Asked Questions Ethernet LED does not light upCan I make calls while I’m browsing the Internet? Network Neighborhood/My Network Places Appendix B Windows HelpShared Resources Appendix B Windows Help Appendix C Glossary Appendix C Glossary Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Appendix D Specifications Mm x 101 mm x 15 mm Dimensions 98 x 3.98 x H x DStorage Humidity ~90% Non-Condensing Appendix E Warranty Information Limited WarrantyAppendix E Warranty Information Appendix F Regulatory Information FCC StatementAppendix F Regulatory Information Toll-free from US VonageLinksys