C The Router’s Web-based Utility will appear with the System Summary screen showing. Click on the Setup tab, which is the next tab over, then con- tinue with the instruction, below, to complete the Net- work page.

D Depending on the setup infor- mation from your ISP, you may need to provide a host name and domain name for the Router. The Host Name and Domain Name fields are usu- ally left blank. If requested by your ISP (usually cable ISPs), complete these two fields.

E Choose the internet interface you wish to use, the RJ45 or the SFP. Only one of these ports can be used at the same time.

F In the drop-down menu for the WAN Connection Type setting features four Internet connec- tion types: obtain an IP auto- matically, Static IP, PPPoE, and PPTP. Depending on which con- nection type you select, the features available on the Net- work page of the Setup screen will differ. Proceed to the instructions for the connection type you are using.

C

D

1 Obtain an IP Automatically

aIf your ISP says that you are connecting through DHCP or a dynamic IP address from your ISP, then select Obtain an IP automatically as the WAN Connection Type. If you also select Use the Following DNS Server Addresses, enter a spe- cific DNS Server IP Address.

bClick the Save Settings button, and go to Step G.

2 Static IP

aIf your ISP says that you are connecting through a static or fixed IP address from your ISP, then select Static IP as the WAN Connection Type.

bEnter the WAN IP Address, Sub- net Mask Default Gateway Address, and DNS Server pro- vided by your ISP.

cIn the DNS Server fields, enter the DNS address(es) provided by your ISP. You need to enter at least one DNS address.

dClick the Save Settings button, and go to Step G.

Obtain an IP automatically

Static IP

3 PPPoE

aIf your ISP says that you are connecting through PPPoE or if you normally enter a user name and password to access the Internet, then select PPPoE as the WAN Connection Type.

bEnter the User Name and Pass- word provided by your ISP.

cIf you select Connect on Demand, the PPPoE connec- tion will be disconnected if it has been idle for a period longer than the Max Idle Time setting.

dIf you select Keep Alive, the Router will keep the connec- tion alive by sending out a few data packets at the Redial Period, so your Internet service thinks that the connection is still active.

eClick the Save Settings button.

fGo to Step G.

4 PPTP

PPTP is a service used in Europe and Israel only. IF you are using a PPTP connection, check with your ISP for the necessary setup information. When you are finished, go to Step G.

PPPoE

PPTP

G If you haven’t already done so, click the Save Settings button. Then, close the web browser.

H Power your cable or DSL modem off and back on again.

I Restart or power on your PCs so they can obtain the Router’s new settings.

J To test the Router’s settings, open your web browser from any computer. In the browser’s Address field, enter www.linksys.com/registration and press the Enter key.

Congratulations! The installation of

the Router is complete.

J

For additional information or troubleshooting help, refer to the User Guide on the Setup CD- ROM. You can also call or e-mail for further support.

24-hour Technical Support

800-326-7114

(toll-free from US or Canada) E-mail Support

support@linksys.com Website

http://www.linksys.com or http://support.linksys.com

RMA (Return Merchandise Authorization)

http://www.linksys.com/support

FTP Site

ftp://ftp.linksys.com

Sales Information

800-546-5797 (800-LINKSYS)

Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All rights reserved.

RV0041-QI-50505 KL

Page 2
Image 2
Cisco Systems RV0041 Obtain an IP Automatically, Static IP, PPPoE, Congratulations! The installation Router is complete