Citizen JNOXXX Time adjustment, Adjusting the Calendar, Calendar adjustment, Using the Alarm

[Time adjustment]

1.Pull the
M (MODE) button out to the setting position. The time is displayed

in the digital section with the hours, minutes and seconds blinking. (At this point, daylight-saving time ON/OFF can be selected by pressing the
C (SET) button.)

2.Press the
A (SELECT) button. The desired segment of hours, minutes or seconds will blink in sequence. The segments blink in the following sequence: [hours, minutes and seconds] ➡ [seconds] ➡ [minutes] ➡ [hours] ➡ [switching between 12- and 24-hour systems] ➡ [hours, minutes and seconds].

3.Use the
C (SET) button to adjust the blinking segment.

4.Push the
M (MODE) button in to its normal position. Time adjustment is now completed.

Adjusting the Calendar

This page should be read with the watch diagram, on the first page of this manual, showing the location of the parts.

Adjusting the calendar for one of the 30 cities will automatically adjust the calendar for the remaining cities, according to the time differences.

[Preparation for calendar adjustment]

1.Press the
M (MODE) button to move the mode hand to [CAL].

2.Press either the
A (UP) button or
C (DOWN) button to select the desired city.

[Calendar adjustment]

1.Pull the
M (MODE) button out to the setting position. The day of the week (MO, TU, etc.) displayed in the digital

section disappears and the month number starts blinking.

2.Press the
A (SELECT) button. The desired segment of the date will blink in sequence.

The segments in the following sequence: [month] ➡ [date] ➡ [year] ➡ [month]

3.Use the
C (SET) button to adjust the blinking segment.

4.Push the
M (MODE) button in to its normal position. Calendar adjustment is now completed. *There is no need to adjust the day of the week since it is corrected automatically.

Using the Alarm

This page should be read with the watch diagram, on the first page of this manual, showing the location of the parts.

The operation of Alarms 1[AL-1], 2[AL-2] and 3[AL-3] are the same; only their tones are different. Once an alarm is set, it sounds at the same time every day until it is cancelled (set to OFF).

[Preparation for alarm setting] Example: Setting AL-1

1.Press the
M (MODE)

button to move the mode hand to [AL-1].

2.Press either the
A (UP) or
C (DOWN) button to select the desired city.

[Alarm setting]

1.Pull the
M (MODE) button out to the setting position.

2.Press the
A (SELECT) button. The desired segment of the time will blink in sequence.

The segments blink in the following sequence: [Alarm ON/OFF] ➡ [hours] ➡ [minutes] ➡ [alarm ON/OFF]

3.Use the
C (SET) button to adjust the blinking segment.

4.Push the
M (MODE) button in to its normal position. Alarm adjustment is now completed.

5.Press the
M (MODE) button to return the mode hand to [TME].

*To turn the alarm off, press either the
A ,
B ,
C or
M button.

Using the Chronograph

This page should be read with the watch diagram, on the first page of this manual, showing the location of the parts.

In addition to the normal function of measuring the time from a starting to a stopping point, this chronograph has a split time function that enables you to measure elapsed time at any point from start to finish.

[Preparation for using the chronograph] Press the
M (MODE) button to move the mode hand to [CHR].

[Using the chronograph - 1]

1.Pressing the
A (START) button starts time measurement.

2.Pressing the
A (STOP) button stops time measurement.

3.Pressing the
C (RESET) button returns the

displayed numbers to zeros.

[Using the chronograph - 2]

1.Pressing the
A (START) button starts time measurement.

2.Pressing the
C (SPLIT) button returns the elapsed time for 10 seconds. (This function is useful in measuring elapsed time upon passing a point during a marathon, etc.)

3.Pressing the
A (STOP) button stops the time measurement.

4.Pressing the
C (RESET) button returns the displayed digits to zeros.