Installation

Mounting/Cables

 

 

Installation

CAUTION: To avoid fire, do not cover or obstruct ventilation openings. Do not install invert- er in a zero-clearance com- partment. Overheating may result.

WARNING: This unit contains components which can pro- duce arcs or sparks. To prevent fire or explosion, do not install in compartments containing a battery or flammable mater- ials, or in a location which requires ignition protected equipment.

Installation

The inverter must be installed in an area that meets all of the following requirements:

A.Dry- Do not place in an area where water can drip or splash on the inverter.

B.Cool- Ambient air temperature should be between 30° F and 105° F (0° C and 40° C). The cooler the better.

C.Ventilate- Allow at least 1 inch (3cm) of clear- ance around the inverter for proper airflow. Make sure that ventilation openings on the ends of the unit are not obstructed.

D.Safe- Do not install the inverter in the same compartment as a battery or in any compart- ment that contains flammable liquids such as gasoline.

E.Close to battery- Install unit as close to bat- tery as possible (without being in the same compartment) to minimize the length of cable required to connect the inverter to the battery. It is better and cheaper to run longer AC wires than longer DC wires (cables).

Mounting

Mount the inverter on a flat surface placing the mounting bracket on the bottom. Mounting hardware should be corrosion resistant and at least #10 or larger. The inverter can be mounted horizontally or vertically.

Cables (included)

Power wire and wiring is very important to the performance of the inverter. Because the inverter has a low voltage, high current input, low resis- tance wiring is essential between the battery and inverter. This is so it can deliver the maximum amount of energy to the load.

Use only copper wire. Aluminum wire has about 1/3 more resistance than copper wire of the same size plus it is difficult to make good, low- resistance connections to aluminum wire.

We recommend #4 copper cable (90° C insulation rating) as the minimum size for connections between the battery and inverter.

Keep the cable length as short as possible, no more than 4 ft. (1.5 meters). This will keep the voltage drop to a minimum.

Mounting

CAUTION: The inverter must only be connected to batteries with a nominal output voltage of 12 volts. It will not work with a 6 volt battery, and will be damaged if it is connected to a 16 volt battery.

WARNING: If you are making a permanent AC connection to the inverter, make sure that the AC wiring steps are performed before any DC wiring is done. (DC hook-up energizes internal components, regardless of the position of the ON/OFF switch). Working on AC connections in such a circumstance may result in an electric shock.

WARNING: 115 Volt AC power is potentially lethal. Do not work on AC wiring when it is connect- ed to the inverter (even if it is switched off) unless the DC power source is physically dis- connected from the inverter. Also, do not work on AC wiring if it is connected to another AC power source such as a genera- tor or the utility line.

8

9

 

 

Page 8
Image 8
Cobra Electronics HG-PI1000 manual Installation Mounting/Cables

HG-PI1000 specifications

Cobra Electronics has long been a leading name in communication devices, and their HG-PI1000 model exemplifies the brand's commitment to cutting-edge technology and user-friendly design. This high-performance radio is specifically engineered for use in a variety of environments, whether it be on the road, at work, or during outdoor adventures.

One of the standout features of the Cobra HG-PI1000 is its robust power output. With a maximum power rating of 1000 watts, it offers exceptional range and clarity, ensuring reliable communication even in challenging conditions. This power output is complemented by a high-efficiency amplifier, which not only enhances the transmission capabilities but also optimizes battery consumption—an essential factor for extended use.

The HG-PI1000 integrates advanced digital signal processing (DSP) technology, providing crystal-clear audio quality free from interference and distortion. This sophistication enables users to detect even the faintest signals, making it a great choice for both professionals and outdoor enthusiasts who require dependable communication equipment. Its built-in noise reduction features further enhance the clarity of received signals, making conversations smooth and effective.

User convenience is prioritized in the design of the HG-PI1000. The unit features a large, easy-to-read LCD display that provides crucial information such as signal strength, battery level, and transmission status at a glance. The intuitive interface allows users to easily navigate settings and features, while programmable buttons give quick access to frequently used functions.

Additionally, the Cobra HG-PI1000 is built with durability in mind; it features a rugged casing that is resistant to shocks and impacts. This makes it suitable for use in harsh outdoor environments, whether you're hiking, camping, or working in demanding settings. The weatherproof design also ensures that the device can withstand the elements, providing peace of mind no matter where you go.

Furthermore, the HG-PI1000 supports various communication modes, making it versatile for different applications. From basic voice communication to more advanced data transmission, this radio is equipped to handle diverse communication needs. Its long-lasting battery life means that users can stay connected for extended periods, an essential feature for remote operations.

In summary, the Cobra Electronics HG-PI1000 stands out for its impressive performance, user-friendly design, and rugged durability. Whether used in professional settings or during personal adventures, its advanced features make it an excellent choice for anyone in need of a reliable communication tool. With the HG-PI1000, Cobra Electronics continues to set high standards in the world of communication technology.