Reference
This chapter discusses ways to troubleshoot the DTV-102 converter box and provides the module specifications.
5.1 Troubleshooting Guide
If you are experiencing problems with the DTV-102, see Table 1 for available solutions.
Table 1. DTV-102 Module Troubleshooting

- 32 -

Symptom Solution
No power
Make sure the power supply is securely plugged into a standard wall outlet and the
cord is plu gged i nto the p ower conne ctor on the CB modu le.
Make sure the CB module is turned on using the front panel power button or the
remote control power button.
CB is not responding to the
remote control
Make sure to point the remote control directly at the remote control sensor on the
CB, with no obstacles in between them.
You may be too far from C B. Try movin g closer .
Make sure that the remote control batteries are installed in the correct direction (+
and –).
The batteries may be depleted. Try replacing them with new ones.
Verify CB is operating correctly by pressing buttons on the front panel of CB.
No picture
Make sure that the antenna in cable is correctly connected to the CB.
Make sure that the video out cable is correctly connected to the CB and TV.
Make sure that the CB and TV are turned on.
Make sure that the TV is correctly set to the selected CB video output channel.
Refer to the TV owner’s manua l for further information.
Check the antenna and the antenna cable. There may be damage or interference
sources.
Picture is blocky or not clear
Check the antenna and the antenna cable. There may be damage or interference
sources.
Reposition the antenna to improve signal strength. Signal strength can also be
affected by rain or snow. In the USA, the website www.antennaweb.org can
provide help in determining the bes t antenna orientation.
No sound
Make sure that the audio cables are correctly connected between the CB audio
outputs and the TV audio inputs .
Make sure that CB and TV are turned on.
Make sure the CB and TV volume settings are at a reasonable level.
Make su re tha t the M UT E functi on is not ac tiva ted on th e CB or T V .
Make su re the TV is c orre ctly s et to the s elec ted C B audi o outpu t chan nel.
When TV has only one audio input jack, use a standard audio cable (white) to
connect the audi o output j ack (white ) on the C B to the a udio i nput ja ck on the T V.
The red audio cable and the CB red audio output jack are not needed.
Reference
5.2 Specifications
Product
Converter Box for ATSC to NTSC
Connecting Jacks
ANT IN
F connector (75 ohm)
ANT OUT
F connector (75 ohm)
Video Output
1-pin RCA jack, 1Vpp, 480i composite
Analog Audio Output
2-pin RCA jack (L, R), 450 mVrms (100k ohm)
RF Input
DTV standard ATSC
Channel Coverage
Terrestrial: 2-69
Power Source
100-240 VAC, 50/60 Hz +/-0.5 %

- 33 -

All digital channels a re not
received
Make su re tha t the A uto P rogra m pro ces s i n the C ha nnel m enu h as been
completed. It will be required whe n you se tup the CB for the first time o r when the
CB is moved to a location whe re other cha nnels a re broadc ast.
The selected channel does not exist at the time. There are not always
sub-channels being broadcas t.
When the Auto Program proces s is interrupted a nd not completed, some c hannels
will not be received. Ma ke sur e to complete the Auto Pro gram proce ss in the
Channel menu.
CC display stays on or two
sets of captions are shown
Make sure the CB CC mode is set to Off.
Make sure that the TV’s CC display is turned off. Refer to the TV owner’s manual
for further information on how to turn off its CC feature.
Forgot the PIN for V-Chip Unplug the A C po wer c ord a nd wa it for a pprox . 5 s ec onds , the n plu g in the power
cord. I n the V -C hip m enu, ente r the d efa ult num ber "0 000 ."
Power Consumption
w/o smart antenna, 8W (Power on),
Operating Condition
41 F° (5 C°) - 104 F° (40 C°)
Board Dimensions
(241 mm x 168 mm x 43 mm)
Weight
425g
Accessories
Remote Control 1 (Provided)
Batteries (size AAA) 2 (Provided)
RF cable 1
RCA cable
(Video+Audio L/R) 1
Designs and Specifications are subject to change without notice.