The remote control can perform the following functions:
•Turn the system ON and OFF
•Select operating mode
•Adjust room air temperature and fan speed
•Set time periods for automatic system operation
BATTERY INSTALLATION — Two AAA 1.5V alkaline batteries (included) are required for operation of the remote control. See Fig. 2 for battery location.
To install batteries:
1.Remove battery compartment cover by sliding off of remote.
2.Insert batteries being sure to follow polarity markings in- side battery compartment.
3.Replace battery compartment cover.
NOTE: Replace batteries whenever “Low battery” indicator appears on remote control display panel.
DISPLAY SCREEN — There are five operating mode indica- tors that appear on the remote control display screen. See Fig. 3.
OPERATION
Remote Control Operation — The remote control has 3 buttons (see Fig. 4) used for operating and controlling the system:
•MODE button — changes operating mode
•UP/DOWN button — selects desired operating mode
•ON/OFF button — turns the system on or off and trans- mits programing selections to unit.
BACK OF
REMOTE CONTROL
2 AAA 1.5V BATTERIES
BATTERY COMPARTMENT
COVER
Fig. 2 — Location of Batteries on Remote Control
I | I I I |
|
I | ||
I | I | |
I |
| I |
I |
| I |
I |
| |
I | I | I |
I |
| |
| I I |
|
COOLINGHEATING
FAN ONLY | DEHUMIDIFICATION |
A
AUTO
Fig. 3 — Operating Mode Indicators on
Remote Control
NOTE: When transmitting a command from the controller to the unit, be sure to point the controller toward the right side of the unit. See Fig. 4. The unit will confirm receipt of a com- mand by sounding 2 audible beeps.
IMPORTANT: If no changes are made within 10 sec- onds, the remote control will return to its previous setting.
FAN SPEED — To select the Fan mode and change the Fan Speed, follow the steps below:
1.Press MODE button to select the Fan mode.
2.Press UP/DOWN button to select desired fan speed or to Auto.
3.Press ON/OFF button to send changes to unit from re- mote control.
NOTE: If unit is operating in DEHUMIDIFICATION mode the fan will only operate in Low speed and cannot be changed.
TEMPERATURE SETTINGS — The temperature settings can be easily changed by pointing the controller toward the unit and pressing the UP/DOWN button until desired temperature appears on screen. The 
symbol appears each time the ON/ OFF button is pressed.
Another way of changing the temperature is as follows:
1.Select the temperature display by pressing the MODE button. The degree symbol will flash next to the digits on the screen.
2.Press UP/DOWN button to select the desired tempera- ture. The available temperature range is from 54 F to 90 F.
3.Press ON/OFF button to send changes to unit from re- mote control.
AIRFLOW DIRECTION — Perform the following steps to change the direction of airflow from the unit:
1.Press MODE button to select the Sweep function.
2.Press the top of the UP/DOWN button to move the air deflector on the unit in an up and down motion. The air- flow symbol displays motion.
3.Press the bottom of the UP/DOWN button. The airflow deflector stops at a given angle. The airflow symbol dis- play remains in a fixed position.
4.Press ON/OFF button to send changes to unit from re- mote control.
NOTE: If placing the air deflector in a fixed position is chosen, the deflector stops at the angle in which it was located when the ON/OFF button was pressed.
SETTING CLOCK
1.Slide down front cover of controller below ON/OFF but- ton. See Fig. 4.
2.Press CLOCK button using the tip of a pen or paper clip. See Fig. 5.
3.Press UP/DOWN button to set minutes.
4.Press MODE button. The hour digits will flash.
5.Press to UP/DOWN button to set the hour.
6.To confirm current clock settings, press CLOCK button once again using the tip of a pen or paper clip. The remote control will automatically go back to previous display and the clock is displayed.
3
