Computer Expressions 38CG, CS018-030, 40CG manual Timer Display Set Up on Remote Control

2.Press the TIMER button. Each time the button is pressed the next Start or Stop set time appears on the display. See Fig. 6.

3.Press UP/DOWN button to set the time.

4.To set another time period, press the TIMER SET button to go to another time period and repeat steps 2 and 3 above.

5.Press the SET button to set the displayed time when done. See Fig. 7.

NOTE: If changes are not made within 10 seconds, the remote control will return to its previous display. To correct an error, the programmed Timer settings must be cancelled and re- entered. See Canceling Daily Timer section.

Sleep Timer — The Sleep Timer function allows the desired temperature to be updated while the occupant is sleeping. The temperature in the room air gradually rises until this time peri- od is exited. The unit will then return to the previous tempera- ture set. To set the Sleep Timer, follow the steps below:

1.Slide down front cover of controller below ON/OFF but- ton. See Fig. 4.

2.Press the TIMER button until Sleep function is reached.

3.Select the “SLEEP” timer period.

4.Press UP/DOWN button to set the start time and press Timer button to set stop time.

5.Press the SET button to set the display time when done. See Fig. 8.

Setting Daily Timer — Time periods can be programmed to operate the system at set times during a 24-hour period. This timer function can be used for all 3 time periods and sleep peri- od described above.

NOTE: The daily timer operates only when there is a direct line of sight between the controller and the unit.

1.Slide down front cover of controller below ON/OFF but- ton. See Fig. 4.

2.Press the TIMER button to select the time period that will be activated daily.

3.Press and hold the SET button until the word “DAILY” appears on the display. See Fig. 9.

4.Press the SET button again to confirm the daily operation for the selected time period. Be sure to point remote con- trol toward the unit while pressing the SET button.

S TA R T		S TA R T		S TA R T
	S TO P		S TO P	S TO P
1	1	2	2	3

Fig. 6 — Timer Display Set Up on Remote Control

	S TA R T
TIMER	S T O P
INDICATOR	1 2	3	S L E E P

DA I LY
MODE			FAN	SWEEP
II I I
I	II
II		I
I		I
I		I
II II
A			A

Fig. 7 — Set Timer Indicator on

Remote Control Display

SLEEP

TIMER	S TA R T
	S TO P
INDICATOR

1	2	3		S L E E P
DA I LY
	MODE			FAN	SWEEP
	II I I
	I	II
	II		I
	I		I
	I		I
	II II
	A			A

Fig. 8 — Sleep Timer Indicator on

Remote Control Display

Canceling Daily Timer — This function will cancel the se- lected Daily Timer program.

1.Slide down front cover of controller below ON/OFF but- ton. See Fig. 4.

2.Press the TIMER button to select the time period that will be activated daily.

3.Press the SET button and hold until the word “DAILY” disappears on the display.

4.Press the SET button again to remove the daily operation from the selected time period. Be sure to point remote control toward the unit while pressing the SET button.

Canceling Specific Start/Stop Time Period — One or more timers can be cancelled by performing the following steps:

1.Slide down front cover of controller below ON/OFF but- ton. See Fig. 4.

2.Press the TIMER button and select desired Timer to can- cel (1,2,3 or Sleep).

3.Press CLEAR button to cancel the selected Timer period. The Start/Stop times will disappear from the display.

4.Press the SET button to confirm the cancellation. Be sure to point remote control toward the unit while pressing the SET button.

Canceling All Time Periods — All timers can be cancelled by performing the following steps:

1.Slide down front cover of controller below ON/OFF but- ton. See Fig. 4.

2.Press the TIMER button.

3.Press and hold the CLEAR button until all Start/Stop times disappear from the display.

4.Check to be sure timer light is off on unit.

5.Press the SET button to confirm the cancellation. Be sure to point the remote control toward the unit while pressing the SET button.

ROOM AIR TEMPERATURE DISPLAY — The current room air temperature is automatically displayed when the remote controller is powered off. To display the room air temperature when the unit is powered on:

1.Slide down front cover of controller below ON/OFF button. See Fig. 4.

2.Press the ROOM button. The current room air tempera- ture will be displayed for several seconds, then disappear.

See Fig. 10.

5