IMPORTANT SAFETY
INSTRUCTIONS
WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE TAKEN, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING APPLIANCE.
DANGER- TO REDUCE THE RISK OF ELECTRIC SHOCK: ALWAYS UNPLUG THIS APPLIANCE FROM THE ELECTRICAL OUTLET BEFORE CLEANING.
1.Unplug from outlet before putting on or taking off parts.
2.This mirror should not be used by or near children or individuals with certain disabilities.
3.Use this mirror only for its intended use as described in these instructions. Do not use attach- ments not recommended by the manufacturer.
4.Never operate this mirror if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the mirror to a service center for examination and repair.
5.Keep the cord away from heated surfaces.
6.Never drop or insert an object into any opening.
7.Do not use outdoors.
8.Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
9.To disconnect, turn all controls to the off position, then remove plug from outlet.
10.Unplug the appliance from outlet before cleaning. Do not leave appliance unattended when it is
plugged in.
11.Be sure mirror is not in a position where it can reflect sunlight; reflected sunlight can cause fire.
12.Do not use on a soft surface such as a bed, where openings may be blocked.
13.Touch mirror base until light shuts off, allow unit to cool and unplug cord before replacing light bulbs.
14.Do not place or store appliance where it can fall or be pulled into a tub or sink.
15.If an appliance falls into water, unplug it immedi- ately. Do not reach into the water.
16.To protect against electrical hazards, do not use while bathing or in the shower.
17.Never use while sleeping.
18.Do not use a bulb greater than 20 watts.
Use on any 120 volt 60 hertz AC electric outlet (ordinary house current). Do not use it on any other electrical outlet. There is an electric outlet in the base. Do not plug any appliance over 12 amperes into
the base.
FOR HOUSEHOLD USE ONLY
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
To reduce the risk of electric shock, this mirror has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
Figure 1
CAUTION: BE SURE DIRECT SUNLIGHT DOES NOT
STRIKE MAGNIFYING SIDE OF MIRROR WHEN LEFT UNATTENDED; REFLECTED SUNLIGHT CAN CAUSE FIRE.
1.Your Infiniti™ by Conair® makeup mirror will rotate 360° so that you can use either the standard, flat mirror or the 7x magnifying mirror located on the opposite side.
2.The mirror is uniquely designed with a 10x spot
magnification mirror which helps to flawlessly shape eyebrows, apply makeup, or insert contact lenses.
3.Plug into any standard 120 volt wall outlet. The mirror light is activated by touch. Touch the base to control the light settings. The first touch will turn the light on to the low setting. A second and third touch will change light settings to medium and high. A fourth touch will turn off the mirror light.
4.After use, always touch the base to turn the mirror to the off position and unplug.
5.This mirror features an electrical outlet in the base. Power ratings on appliances plugged into this electrical outlet should not exceed 12 amperes (Figure 1).
6.The beauty and design of this mirror complements any decor. Therefore, you may wish to leave the mirror displayed. However, if you choose to store the mirror, see “STORAGE” for detailed information.
TO Replace Bulb
CAUTION: TURN OFF POWER AND UNPLUG. ALLOW TO COOL AT LEAST 3 MINUTES BEFORE REPLACING BULB. Replace bulb only with bulb of same wattage rating.
Contact a Conair service center at
1.Remove screws from left and right sides of mirror (Figure 2).
2.Carefully lift off the removable housing from the half that is affixed to the stand.
3.Unscrew the old bulb and replace with the
new bulb (Figure 3).
Figure 2
Figure 3
