Manuals / Cooper Bussmann / Lawn and Garden / Landscape Lighting

Cooper Bussmann 858 instruction manual 10.8Checking the Second LEED MODULE

Models: 858

1 63

Download 63 pages 42.25 Kb

Page 21

10.8Checking the Second LEED MODULE

DOCUMENT 1025

REV. B

Instruction Manual

AGS-LED

858 LED Series

Sizes 1, 2, 3, 4 and 5

Turn off power to the sign by turninng off the corresponding Constant Current Regulator (CCR) power. (WARNING: Wait five minutes after sign power is turned off to service the sign. This will allow any residual high voltage stored i n Power Supply PCB components to bleed off.) With your multimeter set to DC Volts, verify that the Power Supply Output Voltage is less than 30-VDC at TP6 (Positive lead) and TP3 (Negative Lead) as indicated in Figure 22. If the Power Supplyy Output Voltage is greater than 30-VDC, then you m ust wait until the Power Supply Output Voltage drops below 30-VDC before you proceed with the next steep.

Remove the black return cable connnector from the last LED MODULE output cable connnector (see Figures 7-11 & 20). Replace the ouutput cable connector in the first LED MODULE witth the black return cable connector. Turn on main powwer. If the first LED MODULE momentarily lights and then turns off, then the first LED MODULE and thhe Power Supply LED cable and Power Supply board are operating normally.

Turn off main power to the sign. Wait five minutes for the power supply voltages to dissipate. Verify that the output voltage is less than 30-V DC with a multimeter as described in the opening paaragraph of this section. Replace the black return cable connector with the first LED MODULE output cable connector. If the sign does not light at all, then replace the LED MODULE #1 and/or the cable con necting from the output of the Power Supply to the innput of LED MODULE #1(see Section 10.10). Thenn repeat the test described above in this section.

10.8Checking the Second LEED MODULE

WARNING

WARNING:

Failure to t urn off power to the sign and wait five minutes could result in severe injury or death.

Turn off power to the sign by turninng off the corresponding Constant Current Regulator (CCR) power. (WARNING: Wait five minutes after sign power is turned off to service the sign. This will allow any residual high voltage stored i n Power Supply PCB components to bleed off.) With your multimeter set to DC Volts, verify that the Power Supply Output Voltage is less than 30-VDC at TP6 (Positive lead) and TP3 (Negative Lead) as indicated in Figure 22. If the Power Supplyy Output Voltage is greater than 30-VDC, then you m ust wait until the Power Supply Output Voltage drops below 30-VDC before you proceed with the next steep.

Remove the black return cable connnector from the last LED MODULE output cable connnector (see Figure 20). Replace the output cable conneector in the second LED MODULE with the black return cable connector. Turn on main power to the sign. If both LED MODULES momentarily lightt and then turn off

13

Image 21

Cooper Bussmann 858 instruction manual 10.8Checking the Second LEED MODULE

Contents

Airside Guidance Sign AGS-LED 858 LED Series Instruction ManualSizes 1, 2, 3, 4 and DOCUMENT1025 REVISIONB July 14,1Revisions 2Limited Product Warranty 3 Safety Notices 3.1Keep Away from Live Circuits3.2RESUSCITATION DANGER 4 Safety Symbols 4.1DangerDANGER 4.2Warning5Test Equipment and Tools 6Table of Contents 7List of Figures and Tables 8.2Classification of Signs 8General Information 8.1General Description8.3Part Numbers DOCUMENT REV. B Instruction Manual AGS-LED858 LED Series Sizes 1, 2, 3, 4 and NOTICE InstallationDANGER DANGERDOCUMENT REV. B Instruction Manual AGS-LED 10 Maintenance and Troubbleshooting 10.1General5345-44J series circuiit power at its source adhesive surfaces before installing10.2Problem Solving Guide PROBLEMCORRECTIVE ACTION PROBLEMPOSSIBLE CAUSE POSSIBLE CAUSE PROBLEMCORRECTIVE ACTION MODULEs See SecDOCUMENT REV. B Instruction Manual AGS-LED 10.5Checking Power Supplyy LED Cable 10.7Checking the First LED MODULE 10.6Checking LED MODULLE Cable Connections10.8Checking the Second LEED MODULE 10.9Continue Checking the Rest of the LED MODULES 10.10 Replacing an LED MODDULE LED MODULE see Section 10.11 Sign PC Board P/N 62277 Calibration see Section 858 LED Series Sizes 1, 2, 3, 4 and DOCUMENT REV. B Instruction Manual AGS-LEDFigure 1. Single module sign 11 Figures and TablesSizes 1, 2, 3, 4 and Instruction Manual AGS-LED 858 LED SeriesDOCUMENT 1025 REV. B Figure 2. Double module signDOCUMENT REV. B Instruction Manual AGS-LED 858 LED Series Sizes 1, 2, 3, 4 andFigure 3. Three module sign DOCUMENT REV. B Instruction Manual AGS-LED 858 LED Series Sizes 1, 2, 3, 4 andFigure 4. Four module sign Sizes 1, 2, 3, 4 and Instruction Manual AGS-LED 858 LED SeriesDOCUMENT 1025 REV. B Figure 5. Distance MarkerDOCUMENT REV. B Instruction Manual AGS-LED 858 LED Series Sizes 1, 2, 3, 4 andFigure 6. Sign Options 858 LED Series Sizes 1, 2, 3, 4 and DOCUMENT REV. B Instruction Manual AGS-LEDDOCUMENT REV. B Instruction Manual AGS-LED Figure 8. LED Array Wiring, One Module Signs858 LED Series Sizes 1, 2, 3, 4 and Reference Figure 7 for LED array orientationsDOCUMENT REV. B Instruction Manual AGS-LED Figure 9. LED Array Wiring, Two Module Signs858 LED Series Sizes 1, 2, 3, 4 and Reference Figure 7 for LED array orientationsDOCUMENT REV. B Instruction Manual AGS-LED Figure 10. LED Array Wiring, Three Module Signs858 LED Series Sizes 1, 2, 3, 4 and Reference Figure 7 for LED array orientationsDOCUMENT REV. B Instruction Manual AGS-LED Figure 10. LED Array Wiring, Four Module Signs858 LED Series Sizes 1, 2, 3, 4 and Reference Figure 7 for LED array orientationsDOCUMENT REV. B Instruction Manual AGS-LED Figure 11. LED Array Wiring, Distance Marker858 LED Series Sizes 1, 2, 3, 4 and Reference Figure 7 for LED array orientations858 LED Series Sizes 1, 2, 3, 4 and DOCUMENT REV. B Instruction Manual AGS-LEDDOCUMENT REV. B Instruction Manual AGS-LED 858 LED Series Sizes 1, 2, 3, 4 andFigure 12a. Expanded left section of Figure DOCUMENT REV. B Instruction Manual AGS-LED 858 LED Series Sizes 1, 2, 3, 4 andFigure 12b. Expanded right section of Figure DOCUMENT REV. B Instruction Manual AGS-LED 858 LED Series Sizes 1, 2, 3, 4 andFigure 12c. Expanded top section of Figure Instruction Manual AGS-LED 858 LED Series Sizes 1, 2, 3, 4 andDOCUMENT 1025 REV. B Instruction Manual AGS-LED 858 LED Series Sizes 1, 2, 3, 4 andDOCUMENT 1025 REV. B Figure 15. Concrete Foundation/Pad configurations: Two 4-ModuleSigns, Side by Side Instruction Manual AGS-LED 858 LED Series Sizes 1, 2, 3, 4 andDOCUMENT 1025 REV. B 858 LED Series Sizes 1, 2, 3, 4 and Figure 18. Power Supply Box DOCUMENT REV. B Instruction Manual AGS-LED858 LED Series Sizes 1, 2, 3, 4 and Figure 21. Power Supply Wiring Diagram DOCUMENT REV. B Instruction Manual AGS-LED858 LED Series Sizes 1, 2, 3, 4 and 858 LED Series Sizes 1, 2, 3, 4 and DOCUMMENT REV. B Instruction Manual AGS-LEDL858 AGS L858 AGS CCHALP 858 LED Series Sizes 1, 2, 3, 4 and DOCUMENT REV. B Instruction Manual AGS-LEDCCHALP Sign VA Sign Sign Regulator Setting Regulator SettingRegulator Setting Current Range A, RMSFault GreenGreen DOCUMENT REV. B Instruction Manual AGS-LED DOCUMENT