B.Place ice bank control sensing bulb in product coils basket holder. BE CAREFUL NOT TO KINK CAP-

ILLARY TUBE. COIL EXCESS TUBE AND PLACE IN A SAFE AREA.

C.Install new ANODE (item 2) in product coil basket holder.

D.Connect anode wire to evaporator tank using aluminum SHEET METAL SCREW (item 3).

E.Install dispensing valves, plate gasket, and plate on unit and secure with shank nuts.

F.Connect product lines to back of dispensing valve sleeves.

G.Make sure rubber washers are in place on tank coil line fittings.

H.Remove water fill plug from water fill hole in agitator motor and cover assembly.

I.Using hack saw (see Figure 1), cut out corner of cover assembly water fill hole enough to fit over lines connected to new copper evaporator coil.

J.Very carefully, place agitator motor and cover assembly in unit. Secure cover assembly in unit with screws.

K.Secure product coil line fittings to cover assembly with hex nuts.

L.Connect agitator motor ground wire and power cord.

M.Connect product inlet line swivel nut connectors to product coil line fittings on cover assembly.

IMPORTANT: Install RUBATEX INSULATION (item 7) on copper tubing as follows:

A.Cut rubatex insulation to length for length of tubing to be insulated.

B.Remove paperback from cut piece of insulation.

C.Lay insulation length wise along copper tubing, then wrap insulation on tubing.

6.Using RUBATEX INSULATION (item 7), wrap accumulator from insulating tubing on bottom of accumulator to solder connection on compressor. MAKE SURE REFRIGERATION PLUMBING AND ITS COM-

PONENTS DO NOT INTERFERE WITH CONDENSER FAN.

7.Using RUBATEX INSULATION (item 7), wrap suction line assembly tubes where they enter evaporator tank.

8.Fill water tank with clean water to top of stainless steel coils located in coil basket. USE LOW-MINERAL-CONTENT WATER WHERE A LOCAL WATER PROBLEM EXISTS.

9.Install unit top cover and secure with four screws.

10.Install lower access grilles on unit.

11.Install unit drip tray.

TESTING

Test run unit to ensure it builds an ice bank (43 lbs.) and shuts off.

7

189159001

Page 7
Image 7
Cornelius 750 Pre-Mix manual Testing, Ponents do not Interfere with Condenser FAN

750 Pre-Mix specifications

Cornelius 750 Pre-Mix is an advanced beverage dispensing solution designed for high-efficiency service in various commercial settings, including restaurants, bars, hotels, and event venues. This system represents the epitome of convenience and versatility, allowing establishments to serve a wide array of soft drinks with minimal hassle.

One of the standout features of the Cornelius 750 Pre-Mix is its compact design, which enables it to efficiently fit into tight spaces, a common challenge in many hospitality environments. The system is engineered to handle both carbonated and non-carbonated beverages, providing versatility in the types of drinks that can be served. Its ability to accommodate diverse beverage options makes it an appealing choice for businesses that want to offer a varied drink menu without the need for multiple machines.

The Cornelius 750 Pre-Mix utilizes cutting-edge technologies to ensure optimal performance. It incorporates advanced refrigeration techniques that maintain beverage freshness and quality. This system also includes a user-friendly interface and intuitive controls, allowing staff to operate and manage drinks with ease, thus enhancing operational efficiency during peak service hours.

One of the characteristic advantages of the Cornelius 750 Pre-Mix is its low-maintenance design. The system features robust components that require minimal upkeep, allowing operators to focus on service rather than repairs. Additionally, it is built with energy efficiency in mind, helping to reduce operating costs while minimizing the environmental footprint.

The construction of the Cornelius 750 Pre-Mix employs high-quality materials that ensure longevity and durability, making it a wise investment for any beverage-serving establishment. The design also prioritizes clean lines and aesthetic appeal, contributing to a professional look that complements any décor.

Overall, the Cornelius 750 Pre-Mix stands out as a reliable and efficient beverage dispensing solution that caters to the needs of modern commercial environments. With its combination of advanced technology, ease of use, and versatile beverage handling capabilities, it is an ideal choice for businesses looking to elevate their drink service experience while maintaining high standards of quality and efficiency.