TROUBLESHOOTING CHART – ICEMAKER NOT OPERATING
NO POWER
Check electrical wiring in con-
trol box for loose connec-
tions.
Check for failed service
switch or relay.
Remote condenser
units only
Remote condenser
not running.
ICEMAKER RUNS BUT DOES NOT MAKE ICE
Condenser fan running but compressor not running
Check line voltage.
Check compressor winding
& components.
LOW WATER SAFETY
SWITCH OPEN
Check that water is turned on.
Check for restriction in water line.
ICEMAKER OPERATING BUT
SOFT ICE
Check bin switch
GEARMOTOR OVERLOAD
TRIPPED
Check water level control and evaporator water tube for lime build up restriction.
Check power to machine.
Check incoming water pressure
(minimum 10 lbs.).
Check water safety switch.
YesNo
No
Yes
|
|
|
|
|
|
|
|
|
| Evaporator water tube |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| may have an air bubble. |
|
|
|
|
|
| |
| High pressure |
| Check electrical |
| Check power |
| Clear air bubble from |
|
|
|
| Clean all related |
| Refer to guide | |||
| switch open or |
| wiring in control box |
| to condenser. |
|
|
|
| drain lines. |
| to Good Ice in | |||||
|
|
|
| tube. |
|
|
|
|
| ||||||||
| cycling on and off. |
| for loose connections. |
|
|
|
|
| High suction pressure |
| Low suction pressure |
|
| service manual. | |||
|
|
|
|
|
|
|
|
|
|
| (30 lbs. or above). |
| (20 lbs. or below). |
|
|
| |
CAUTION
Clear ice from evaporator and auger before re- setting over- load.
CLEAN
see
instructions.
23
Discharge |
|
|
| Too much |
|
| Condenser |
|
| Condenser | |||||||
king valve |
|
| in system. |
| refrigerant in |
|
| fan not |
|
|
| dirty or | |||||
partially |
|
|
|
|
|
| system. |
|
| running. |
|
| restricted. | ||||
closed. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
| Evacuate and |
|
|
|
| Check electrical circuit |
|
| |||||
Open |
|
|
| recharge system. |
|
|
|
|
|
| to fan motor. |
|
| ||||
valve |
|
|
| Clean condenser. |
|
|
|
|
| Check fan motor. |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||
| Low pressure switch open |
|
|
|
|
|
|
|
|
|
| ||||||
|
|
| or cycling on and off. |
|
|
|
|
|
|
|
|
|
| ||||
Head
Pressure
high.
Valve stuck open.
Replace
valve.
TXV not operating properly.
Bulb loose.
Clean and tighten.
Suction line
not
insulated.
Bulb
uninsulated.
Clean and insulate.
TXV bulb lost charge.
Replace valve evacuate and recharge.
IMPORTANT
Icemaker runs when reset but problem has not been found.
Continue checking for overload as follows to guard against future problems
Icemaker runs
Short run trips again in 2 min- utes. Check gear- motor circuit.
Reset
overload.
| Reset but |
| Will not |
| |
| motor does |
| reset. |
| |
| not run. |
|
|
| |
|
|
|
|
|
|
| Check |
|
| Overload |
|
| gearmotor |
|
| hot try |
|
| circuit. |
|
| again. |
|
|
|
|
|
|
|
|
|
|
| Will not |
|
|
|
|
| reset |
|
|
|
|
| replace |
|
|
|
|
| overload |
|
Low on | Remote condenser | Plugged |
| Restricted |
|
|
|
|
| |||
|
| Plugged or |
| Icemaker | ||||||||
refrigerant. | units only | liquid line |
| liquid line. |
| faulty TXV. |
| froze up. | ||||
|
|
| dryer. |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Check for
leaks.
LAC not operating properly (minimum discharge pressure 180 lbs.).
Replace LAC valve, evacuate and recharge system.
Replace dryer.
Evacuate and recharge system.
Check for
kinks or damage to liquid line.
Replace
valve. Evacuate and recharge system.
Check if auger is turning.
No
OVERLOAD GUIDE ELECTRICAL
High or low voltage weak power lines can cause overloads on icemaker restarts High running current. Check motor circuits and start relay – Auger delay failed.
ICEMAKER
Mechanical parts worn. Scored evaporator or auger. Worn thrust bearing. Ice maker not turning off. Failed ice level control.
Over compression. Low water inlet temperature. Restriction in water line from reservoir.
REFRIGERANT
Contaminated charge or bad compressor. Low charge or gas leak.
Low suction pressure. Improper expansion valve sensing bulb. Location or insulation and/or defective expansion valve
630460154
Check drive on | Check gears in |
| Check if extruding |
gearmotor. | gearbox. |
| head is down in |
|
|
| evaporator tube. |
|
|
