Manuals / Country Flame / Household Appliance / Indoor Fireplace

Country Flame Fireplace FP33, FP42, FP37 manual a DAMPER DOOR REMOVAL

Models: Fireplace FP33 FP42 FP37

1 61

Download 61 pages 62.8 Kb

Page 29

FIGURE 11a: DAMPER DOOR REMOVAL

INSTALLING DAMPER DOOR - The rotary controlled damper of your Country Flame Fireplace should be assembled as shown in FIGURE 10 after the fireplace is completely installed. At this time the adjustable damper rod sleeve (C) will be embedded in the masonry veneer and cannot turn. Follow the steps below to complete the installation of

your rotary controlled damper.

1.Begin with the damper door (G) in the fully open position. Insert the damper rod (D) through the adjustable damper rod sleeve (C) from the front of the fireplace.

2.From inside the fireplace guide the washer (J) over the end of the damper rod (D).

3.Reach inside the fireplace and slide the damper screw (E) over the end of the damper rod (D) with the setscrew opening positioned toward the rear of the fireplace.

4.Push the damper rod (D) as far toward the rear of the fireplace as possible. Push the damper screw (E) as far to the front of the fireplace as possible.

5.Mark the damper rod (D) flush with the end of the damper screw (E).

6.Remove the assembly and cut the damper rod (D) off at the mark you made in Step 5.

7.Replace the assembly as in Steps 1 and 2.

8.Insert the damper screw (E) into the damper screw bracket (F) and turn it completely counter clockwise until it seats.

9.Slide the end of the damper screw (E) without the setscrew opening over the end of the damper rod (D) and push both the damper screw (E) and the damper rod (D) toward each other as far as possible.

10.Tighten the setscrew (B) at the back of the damper screw (E).

11.Install the logo handle (A) on the outer end of the damper rod (D), align properly, and tighten the setscrew (B).

NOTE: Always close the damper door when the fireplace is not in use. Closing the damper door during non use periods will prevent airflow into or out of the house thus conserving energy whatever the season may be.

FIGURE 11a: DAMPER DOOR REMOVAL

REMOVING DAMPER DOOR - The rotary controlled damper of your Country Flame Fireplace can be removed if necessary. Whether for fireplace system cleaning or repair, follow the steps listed below to remove the damper. FIGURE 11a can be referenced when

it is necessary to remove the damper door.

Version 7.1	18

Image 29

Country Flame Fireplace FP33, FP42, FP37 manual a DAMPER DOOR REMOVAL

Contents

Installation,Operation& MaintenanceManual VolumeCOUNTRY FLAME TECHNOLOGIES VersionWOODBURNINGPRODUCTONLY SMARTFIREPLACEFURNACESFP-33,FP-37,FP-42Installation, Operation & Maintenance Manual FOR YOUR SAFETYVersion TABLE OF CONTENTSVersion Please keep a copy for your personal records Country Flame Technologies FOREWORD Version SAFETY NOTESviii VersionFIREPLACE FURNACE SAFETY LABEL PP-741 Country Flame Technologies INTRODUCTIONWHAT’S INCLUDED WITH YOUR SMART FIREPLACE? 1ChapterMODEL FIREPLACE FURNACE SPECIFICATIONSMODEL MODELPage STEP 1 - FOOTINGS AND FOUNDATIONS 9 STEPS TO INSTALL A SMART FIREPLACEModel 92” wide x 40” deep x 10” thickVersion FIGURE 2 SINGLE OPENING FIREPLACE SYSTEMSSTEP 2 - CONCRETE PAD & HEARTH EXTENSIONS FIGURE 3 OUTSIDE WALL PAD INSTALLATIONVersion FIGURE 4 INSIDE WALL PAD INSTALLATIONFIREPLACE WALL CONSTRUCTION STEP 3 - FIREPLACE POSITION ON THE CONCRETE PADSTEP 4 - FIREPLACE WALL & CHIMNEY CONSTRUCTION FIGURE 5 MASONRY WALL INSTALLATION STEP 5 - CHIMNEY FLUE INSTALLATIONVersion Angle Iron Model NoDuct Size Flue SizeVersion FIGURE 7A MASONRY CHIMNEY INSTALLATIONFIGURE 7B MASONRY CHIMNEY INSTALLATION FIGURE 8A BLOWER INSTALLATION STEP 6 - BLOWER INSTALLATIONSVersion FIGURE 8B AIR INTAKE GRILLE INSTALLATIONFIGURE 9 PARTS DEFINITION FIGURE 9A HEAT DISCHARGE BOOTVersion STEP 7 - COMPLETION OF MASONRY BRICK FRONTFIGURE 10 DAMPER PARTS STEP 8 - FLUE DAMPER CONTROL INSTALLATIONFIGURE 11a DAMPER DOOR REMOVAL FIGURE 11b DAMPER DOOR CONTROL FIGURE 13 ELECTRICAL JUNCTION BOX STEP 9 - ELECTRICAL SYSTEMFIGURE 12 THERMAL SNAP DISK LOCATION FIGURE 14 ELECTRICAL SYSTEM Version FIGURE 15 OPTIONAL SIDE VENTED FIREPLACE 2ChapterDUCTING OPTIONS Version FIGURE 16a DUCTING SYSTEMS EXAMPLESVersion FIGURE 16b DUCTING SYSTEMS EXAMPLESFIREPLACE FURNACE OPERATIONAL REQUIREMENTS DISPOSAL OF ASHES INTERNAL THERMOSTATUSE OF LIQUID FUELS CREOSOTE FORMATION AND REMOVALVersion WOODHEATING WITH WOOD 4Chapter FIREPLACE FURNACE MAINTENANCE REQUIREMENTSVersion OUTSIDE COMBUSTION AIRPROBLEM TROUBLESHOOTING GUIDESOLUTION CAUSESOLUTION PROBLEMCAUSE Lack of Heat continuedChapter REPLACEMENT PARTSREPLACEMENT PARTS cont’d ELECTRICAL HARDWARE PART DRAWINGSPP-703 Version110 CERAMIC SNAP DISK, PP-91 BLOWER, 525 CFM 2 each per fireplace, PP-558RHEOSTAT 2 each per fireplace, PP-350 PP-558DAMPER LOGO HANDLE, PP-37 THERMOSTAT, PP-563PP-563 PP-80INSULATION FOR TOP, SIDES, FRONT, AND BACK, PP-35 ALUMINUM CLEAN OUT DOORS, 8” x 8,” PP-559PP-35 PP-559ASH DUMP COVER, FP-0000-916 DAMPER DOOR ASSEMBLY, FP-0000-921FP-0000-916 FP-0000-921DAMPER ROD SLEEVE, FP-0000-918 YOKE BRACKET ASSEMBLY, FP-0000-923FP-0000-923 FP-0000-918DAMPER ROD, FP-0000-917 DAMPER ROD ASSEMBLY, FP-0000-920DAMPER SCREW, PP-564 FP-0000-917FP-42FLUE TO HT CHIMNEY ADAPTER, F-42-218 FP-33& FP-37FLUE TO HT CHIMNEY ADAPTER, F-218F-218Optional F-42-218OptionalVersion GRILLE BACK, FP-0000-33 GRILLE FRONT, FP-0000-32FP-0000-32 AIR INTAKE GRILLE FRAME, FP-0000-924 AIR INTAKE GRILLE, PP-560F-560 FP-0000-924Version FP-0000-92525-0051-00 Version LOG GRATE optional, LG-900FP-0000-49 COMPANY LABEL FAN SWITCH LABELWARNING LABELS GRATE WARNING LABEL WARNING LABELS cont’dPP-1333 VersionCountry Flame Technologies 900 George Street Marshfield, MOFold Here Place Stamp HereREQUIRED WARRANTY INFORMATION