FENCE
1.From among the loose parts "find the following:
(1)Fence
(2)Fence Brackets
(2)Fence Segments
(2)Tilt Indicators
(2)Lock Knobs
(4)
(4)1/4 Lock Washers
(4)9132 ID x 9/16 OD x 1t16 Thick Washers
(2)9t32 ID x 17/32 OD x 1t8 Thick Washers
(6)
(6)#8 Flat Washers
(6)
(2)
(2)#10 Flat Washers
1.Attach fence brackets to base using
2.Attach fence segments to fence with #8+32 flat head screws, #8 flat washers and
3.Place assembled fence on machine with fence brackets inside the fence segments.
4.Position lock knobs with 9t32 ID x 17t32 OD x I/8 thick washers thru slots in fence segments and thread into fence brackets.
5.Place square against face of fence and table surface. Bring fence square to table and tighten lock knobs.
6.THERE MUST BE 1/32" TO 1116" gap between the lower edge of the fence and jeinter tables (with table set for 0" cut). To adjust, move fence assembly by loosening the
7.Recheck squareness of fence.
8.Install tilt indicators with
#10 flat washers. Set 0 ° of indicators to 0 ° of segments and tighten the screw.
9, The fence should now be adjusted and will accurately measure angles
to 45 ° Inboard and 45 ° outboard (see adjustments section).
|
|
|
|
|
|
|
|
|
|
|
| LOCK | KNOB |
NOTE; | USE | OF WASHERS |
|
|
|
|
|
|
|
| \ % | ||
LESS | THAN | 118 | THICK |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
MAY | RESULT | IN | FENCE |
| + | g/32 | ID | X | 17/320D |
|
| ||
TIGHTENING | PROBLEMS |
|
| X | 1/8 | THK | WASHER |
| |||||
|
|
|
|
|
| FENCE | SEGMENT |
|
|
| |||
| FENCE |
|
|
|
|
|
|
|
|
|
| NUT | |
|
|
|
|
|
|
|
|
|
|
|
|
| _8 FLAT |
|
|
|
|
|
|
|
|
|
|
|
|
| WASHER |
X 112 FLAT | _ |
| _ |
| _" |
|
| ,+ |
|
|
| ||
HEAD MACHINE | SCREW |
|
|
|
|
|
|
|
|
| |||
FENCE.BRACKET |
|
|
|
|
| X314 HEX |
|
| |||||
|
|
|
|
|
|
| _,._. |
|
|
| TILT | INDICATOR | |
|
|
|
|
|
|
|
|
| CAP | SCREW |
|
| |
|
|
|
|
| // |
| LOCK |
| WASHER |
|
| ||
|
|
| 9t32 | I0 | X 91 IS | GO |
|
|
|
|
|
| |
|
|
| X | 1116 | THK |
|
|
|
|
|
|
| |
|
|
| FLAT | WASHER |
|
| 4' | 10 | FLAT |
|
| ||
|
|
|
|
|
|
|
|
|
|
| X 112 | PAN HEAD | |
|
|
|
|
|
|
|
|
|
|
|
| MACHINE | SCREW |
TILT INDICATOR SHOULD BE LINED UP WITH
._"THE FENCE SEGMENT AT THE 0+MARK+
FENCE EXTENSION
To aid in edge jointing of workpieees 4" and wider, you may extend the fence height, The extension can be constructed of 1" (3t4" thick) stock pine or hardwood.
Use #8 flat head wood screws of sufficient length to securely attach the extension to the fence. Make sure that the head of the screws are below
the surface of the fence so as not to interfere with the workpiece.
114
For extra stability, additional countersunk holes have been provided near the ends of the fence,
+8
