Manuals / Brands / Power Tools / Dust Collector / Craftsman / Power Tools / Dust Collector

Craftsman 152.213371 BLOWER AND MOTOR ASSEMBLY TO BASE ASSEMBLY, G

1 48

Download 48 pages, 9.01 Mb

2,

2,

DO NOT assemble the Dust Collector until you are

sure the tool IS NOT plugged in,

DO NOT assemble the Dust Collector until you are

sure the power switch is inthe "OFF" position,

For your own safety, DO NOT connect the machine

to the power source until the machine is completely

assembled and you read and understand the entire

Owner's Manual,

CASTER TO BASE ASSEMBLY

Fig. 7 B

A

BLOWER AND MOTOR ASSEMBLYTO BASE ASSEMBLY

MAKE CERTAIN THE DUST COLLECTOR iS

DISCONNECTED FROM THE POWER SOURCE.

AB

B

D E

1, Turn base (A) right side up, Align the mounting

hobs at the base of blower and motor assembly (B)

with six pre-drilled hobs (C) in base and fasten with

six 5/16=18 x 5/8" hex head screws (D) and 5/16"

lock washer (E), See figure 8,

2,

insert threaded rod of caster (A) into the hob

located on the underside of base (B) and fasten

with 3/8" lock=washer (C) and 3/8-16 hex nut (D),

See figure 7,

Assemble the remaining three casters to the under-

side of the base in the same manner,

Fig. 9

G

2,

3,

Assemble drum support (F) to the two threaded

hobs inthe corner of base with two 5/16=18 x 5/8"

hex head screws and 5/16" lock washer (G), NOTE:

Do not completely tighten hardware at this time,

See figure 9,

Assemble the remaining drum supports to the base

in the same manner, NOTE: Do not completely

tighten hardware at this time,

11

Contents

Main 's m ST COLL c_uS CAUTION: Customer Helpline Page GENERAL SAFETY iNSTRUCTiONS BEFORE USUNG THE DUST COLLECTOR 21,EACHANDEVERY GUJDEUNES FOR EXTENSION CORDS Fig. 3 24O VOLT O SPECiFiC SAFETY iNSTRUCTiONS FOR DUST COLLECTORS AVAILABLE ACCESSORIES UNPACKING AN{) CHECKING CONTENTS (Figure 4 and Figure 5) Fig. 4 F O p FC CASTER TO BASE ASSEMBLY Fig. 7 BLOWER AND MOTOR ASSEMBLY TO BASE ASSEMBLY AB D E Fig. 9 G Fig. 12 T Fig. 11 Fig. 13 V Fig. 15 iNTAKE PORT TO BLOWER MOTOR ASSEMBLY E Fig. 14 NLTER AND COLLECTION BAG TO DRUM ASSEMBLY A FLEXIBLE HOSE TO iNTAKE PORT ASSEMBLY G F E Page CHANGING MOTOR VOLTAGE 120 VOLT CONNECTION 240 VOLT CONNECTION Page C.F.M.REQUIREMENTSFORTOOLS STATIC PRESSURE FIEQUJF{EMENTS FOR A DUST COLLECTION SYSTEM Static Pressure Requirement Chart 4-inchHoseCoupling 4-inch90-degreeElbow 4-inchYoFitting 4-inchToFitting Page Page i o N O o Page Page anuai Propietario c uS 1-800-897-7709 ,I Sears, Roebuck and Co., Hoffman Estates, JL 60179 U.S.A. Page INSTRUCCIONES GENERALES DE ANTES DE UTILIZAR EL COLECTOR DE POLVO D[RECTRICES PARA LAS EXTENSIONES ELECTRICAS Fig. 3 240 VOLTIOS Fig. 1 TOMACORRmENTES _._ co,c,,oo,,,,oo, JNSTRUCCJONES DE SEGURJDAD ESPECJNCAS PARA LOS COLECTORES DE POLVO 3O ACCESOFHOS DJSPONJBLES DESEMPAQUE Y DEL CONTENJDO (Figura 4 y Figura 5) Fig. 4 F Fig. 5 K O R FERRETERIA NO ILUSTRADA FC ENSAMBLAJE DE RUEDAS PJVOTANTES A LA BASE Fig. 7 B MONTAJE DEL ENSAMBLADO BEL SOPLADOR Y EL MOTOR A LA BASE Fig. 8 D E L Fig. 12 T Fig. 11 U Fig. 13 MONTAJE DEL PUERTO DE ADMJSJON AL MOTOR DEL SOPLADOR Fig. 14 MONTAJE DE LAS BOLSAS DE FJLTRO Y DE RECOLECCJON AL TAMBOR Fig. 16 MONTAJE DE LA IVIANGUERA FLEXIBLE AL PUERTO DE Fig. 17 B G F E CONECTANDO LA HERRAMJENTA A LA FUENTE DE ENERGJA JNTERRUPTOR DE ENCENDJDO/APAGADO \ NJANDO EL JNTERRUPTOR A LA POSJCJON DE "APAGADO" DJSYUNTOR DE CJRCUJTOS CAMBJANDO EL VOLTAJE DEL MOTOR Page REQUISUTOS DE PRESUON ESTATICA PARA UN SUSTEMA DE RECOLECCION DE POLVO Cuadro de Requisitos de Presi6n Estatica Page PROBLEMA CAUSA PROBABLE SOLUCION Page 3_s i $ P Page iiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii 1o800-4- MY- H0 ME (1-8oo-4ee-4ees) ome 1"- 80 0"-488"- 12 22 1-,800,,827,,6655 (u.s.A.> 1,,800,,361 ,,6665 (Canada)