ASSEMBLY

NOTE: References to right or left side of the snow thrower are determined from behind the unit in the operating position (standing directly behind the snow thrower, facing the handle panel).

Removing From Crate

1.Remove screws from the bottom of the crate securing the sides, and ends of the shipping crate.

2.Lift off the top off of the crate and set out of the way of the assembly area.

3.Remove and discard plastic bag that covers unit.

4.Remove any loose parts included with unit (i.e., Operator’s Manual, etc.).

5.Push down on the lower handle and pull unit back out of crate.

6.Make certain the crate has been completely emptied before discarding it.

assembly

1.Make certain the springs at the lower end of the auger and drive cables are securely hooked into their respective actuator bracket before pivoting the handle upward.

a.Place the shift lever in the F6 position.

b.Remove the lower wing knob and carriage bolt from each side of the upper handle. Pull up on upper handle as shown in Fig. 1. Align upper handle with the lower handle. Again,

make certain the springs at the lower end of the auger and drive cables are securely hooked into their respective

actuator bracket. Also, remove any rubber bands securing the cables to the wing nuts.

2.a. Secure the upper handle and lower handle with the two wing knobs and carriage bolts removed earlier.

b.Tighten the two wing knobs already installed in the upper holes to firmly secure the upper handle and support tubes.

3.Align the upper and lower shift rods, then slide the shift rod connector down over the end of the lower shift rod. Tap the connector until the lower rod is completely through the connector. See Fig. 2.

NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to change speeds or direction.

NOTE: If the full range of speeds (forward and reverse) can not be achieved, refer to the “Making Adjustments” section.

4.a. Cut the cable tie securing the chute assembly to the lower chute crank rod for shipping purposes.

b.Remove the internal cotter pin from the upper chute crank. Slide the upper chute crank into the sleeve on the lower chute crank. See Fig. 3.

c.Align the hole in the upper chute crank with the hole in the sleeve (If necessary, use a pair of pliers to assist in aligning holes). Insert the internal cotter pin through the holes to secure the chute crank. See Fig. 3.

5.Remove lock nuts and screws securing one of the flange keepers to the chute assembly.

Figure 1

Figure 2

a

b

Figure 3



Page 5 Page 7
Page 6
Image 6
Craftsman 247.88045 manual Assembly, Removing From Crate, Place the shift lever in the F6 position
Page 5 Page 7

247.88045 specifications

The Craftsman 247.88045 is a versatile lawn tractor designed to simplify lawn care for homeowners who seek both efficiency and ease of use. This powerful machine stands out with its robust features and technologically advanced design, catering to various landscaping needs.

One of the key features of the Craftsman 247.88045 is its powerful 24 horsepower Briggs & Stratton engine. This reliable engine ensures smooth operation and ample power to tackle a variety of terrains and grass types. With a hydrostatic transmission, users can enjoy seamless acceleration and deceleration, allowing for precise control during mowing and maneuvering around obstacles.

The 247.88045 is equipped with a 54-inch cutting deck, which provides a wide mowing path, reducing the time and effort required to cover large lawns. The deck features a dual-blade system, ensuring a clean and even cut, which is essential for maintaining a healthy lawn. Additionally, the cutting height is adjustable, allowing users to choose the perfect height for their grass type and seasonal needs.

Ergonomics are also a major consideration in the design of the Craftsman 247.88045. The seat is comfortable and adjustable, accommodating various driver heights, while the steering wheel is positioned for ease of access and control. The tractor is fitted with a fuel gauge and an easy-to-reach dashboard, which provides essential information at a glance, enhancing the user experience.

Durability and reliability are key characteristics of the Craftsman brand, and the 247.88045 is no exception. Constructed with high-quality materials, this lawn tractor is designed to withstand the rigors of regular use. The robust frame and heavy-duty tires offer stability and traction, making it suitable for uneven terrain and different weather conditions.

For added functionality, the Craftsman 247.88045 can be equipped with various attachments, such as a lawn sweeper or snow plow, making it a multi-season tool for homeowners. Its versatility transforms lawn maintenance into a more manageable task, enabling users to extend the tractor's usability beyond just mowing.

In summary, the Craftsman 247.88045 lawn tractor is a powerful, user-friendly machine that combines advanced technology, ergonomic design, and durable construction. Whether you're maintaining a small yard or a larger landscape, this lawn tractor is a reliable partner for achieving a pristine lawn.
Top Page Image Contents