SERVICE AND MAINTENANCE

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary.

Skid Shoes

NOTE: The skid shoes on this machine have two wear edges. When one side wears out, they can be rotated 180° to use the other edge.

1.Remove the six carriage bolts and hex nuts that secure the two skid shoes to the sides of the auger housing. Refer to Figure 18.

2.Position the new skid shoes and secure with the carriage bolts and hex nuts. Make certain the skid shoes are adjusted to be level.

Shave Plate

1.Remove the hex nuts and carriage bolts that secure the shave plate to the bottom of the housing.

2.Remove the rear most hex nut and carriage bolt securing the back of each skid shoe to the sides of the housing. Loosen the four remaining hex nuts securing the skid shoes.

3.Slide the shave plate out of the off-set slot at the bottom of the housing, and from between the skid shoes and side panels of the housing.

4.With the mounting holes toward the back, slide the new shave plate into position and secure with the fasteners removed previously.

Adjustments

Shift Rod

If the full range of speeds (forward and reverse) cannot be achieved, refer to the figure to the left and adjust the shift rod as follows:

1.Looking underneath the handle panel, note which of the three holes in the shift lever the ferrule is inserted into. Also note the direction of insertion. Then remove the internal cotter pin and flat washer from the ferrule and withdraw the ferrule from the shift lever. See Figure 19.

2.Place shift lever in sixth (6) position or fastest forward speed.

3.Push shift rod and shift arm assembly down sharply as far as it will go to put the drive into the fastest forward position.

4.As necessary, rotate the ferrule up or down the shift rod until the ferrule lines up with the hole from which it was earlier removed. See Figure 19.

5.From the direction noted earlier, insert the ferrule into the proper hole.

6.Reinstall the washer and the internal cotter pin.

Figure 18

Figure 19

Chute Control

The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to the Operation section for instructions.

The remote chute control cables have been pre-adjusted at the factory. Move the remote chute lever on the control panel forward to pivot the upper chute down; move the lever rearward to pivot the upper chute up.

16

Page 15 Page 17
Page 16
Image 16
Craftsman 247.88045 manual Shave Plate and Skid Shoes, Shift Rod, Chute Control
Page 15 Page 17

247.88045 specifications

The Craftsman 247.88045 is a versatile lawn tractor designed to simplify lawn care for homeowners who seek both efficiency and ease of use. This powerful machine stands out with its robust features and technologically advanced design, catering to various landscaping needs.

One of the key features of the Craftsman 247.88045 is its powerful 24 horsepower Briggs & Stratton engine. This reliable engine ensures smooth operation and ample power to tackle a variety of terrains and grass types. With a hydrostatic transmission, users can enjoy seamless acceleration and deceleration, allowing for precise control during mowing and maneuvering around obstacles.

The 247.88045 is equipped with a 54-inch cutting deck, which provides a wide mowing path, reducing the time and effort required to cover large lawns. The deck features a dual-blade system, ensuring a clean and even cut, which is essential for maintaining a healthy lawn. Additionally, the cutting height is adjustable, allowing users to choose the perfect height for their grass type and seasonal needs.

Ergonomics are also a major consideration in the design of the Craftsman 247.88045. The seat is comfortable and adjustable, accommodating various driver heights, while the steering wheel is positioned for ease of access and control. The tractor is fitted with a fuel gauge and an easy-to-reach dashboard, which provides essential information at a glance, enhancing the user experience.

Durability and reliability are key characteristics of the Craftsman brand, and the 247.88045 is no exception. Constructed with high-quality materials, this lawn tractor is designed to withstand the rigors of regular use. The robust frame and heavy-duty tires offer stability and traction, making it suitable for uneven terrain and different weather conditions.

For added functionality, the Craftsman 247.88045 can be equipped with various attachments, such as a lawn sweeper or snow plow, making it a multi-season tool for homeowners. Its versatility transforms lawn maintenance into a more manageable task, enabling users to extend the tractor's usability beyond just mowing.

In summary, the Craftsman 247.88045 lawn tractor is a powerful, user-friendly machine that combines advanced technology, ergonomic design, and durable construction. Whether you're maintaining a small yard or a larger landscape, this lawn tractor is a reliable partner for achieving a pristine lawn.
Top Page Image Contents