RULESFORSAFEOPERATION(Continued)
mNEVER USE IN AN EXPLOSIVE ATMO-
SPHERE. Normal sparking ofthe motor could
igniteflammable liquids, gases, orfumes.
m
m
m
KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use aclean
clothwhen cleaning. Never use brakefluids,
gasoline, petroleum-based products or any
strong solvents to clean your tool.
STAY ALERT. Watch what you are doing and
use common sense. Do notoperate tool when
you are tired. Do not rush.
CHECK DAMAGED PARTS. Before further use
of the tool,a guardor other part that isdamaged
should be carefully checked todetermine that it
willoperate properly and perform its intended
function. Check foralignment of movingparts,
binding of moving parts, breakage of parts,
mounting, and any other conditionsthat may
affect its operation. Aguard orother partthat is
damaged should beproperly repaired or
replaced by an authorized service center unless
indicated elsewhere in this instruction manual.
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol, or any medication.
DRILLING OR DRIVING SCREWS INTO
ELECTRICAL WIRING IN WALLS, CEILINGS,
OR OTHER AREAS CAN CAUSE THE BIT OR
CHUCK TO BECOME ELECTRICALLY LIVE.
Do not touch metalparts whendrilling into awall;
grasp only the insulated handle(s) orplastic
housing when usingthis tool. Makesure hidden
electrical wiring, water pipes, and mechanical
hazards are not in the path ofthe bit when
ddlling into a wall.
INSPECT FOR andremove allnails from lumber
before drilling.
IMPORTANT SAFETY RULES FOR BAI-rERY
TOOLS
Battery tools do not have tobe pluggedinto an
electrical outlet; therefore, they arealways in
operating condition. Be aware of possible
hazards when not using your batterytool or
when changing accessories.
USE ONLY THE CHARGER PROVIDED WITH
YOUR BATrERY TOOL. Do notsubstitute any
other charger. Use of another charger could
cause batterias toexplode causingpossible
serious injury.
m
m
$
DO NOT PLACE BATTERY TOOLS OR THEIR
BAI'FERIES NEAR FIRE OR HEAT. They may
explode.
DO NOT CHARGE BATTERY TOOL IN A
DAMP OR WET LOCATION.
Your battery toolshould be charged in a location
where the temperature is more than 50°F but
lessthan 100°F.
Under extreme usage or temperature conditions,
battery leakage may occur. Ifliquid comes in
contact with your skin,wash immediatelywith
soap and water, then neutralize with lemon juice
orvinegar. If liquid gets in your eyes,flush them
with clean water for at least10 minutes, then
seek immediate medical attention.
If carrying your battery tool at yourside, make
sure it is not running and your finger isnot on the
switch.Avoid accidentalstarting.
SECURE WORK before applying power. NEVER
holdworkpiece inyour hand or across your legs.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER .r"
SAVE THESE INSTRUCTIONS. This manual
contains important safety and operating
instructionsfor batterycharger part number
976790-001.
Before using battery charger, readall instructions
and cautionary markings in this manual, on
battery charger, and productusing battery
charger.
A WARNING: To reduce risk of injury,charge only
nickel-cadmium type rechargeable batteries.
,Other types of batteries may burstcausing
personal injuryand damage.
m
m
Do not expose charger torain or snow.
Use of an attachment notrecommended or sold
bythe batterycharger manufacturer may result
ina riskof fire, electric shock, or injuryto
persons.
To reduce riskof damage tocharger bodyand
cord, pull by charger body ratherthan cordwhen
disconnecting charger.
Make sure cordis located so that itwill not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
4