RULES FOR SAFE OPERATION (Continued)
NEVER USE IN AN EXPLOSIVE ATMO-
SPHERE. Normal sparkingof the motor could
igniteflammable liquids, gases, or fumes.
KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
clothwhen cleaning. Never use brake fluids,
gasoline, petroleum-based products or any
strongsolvents toclean yourtool.
STAY ALERT. Watch what you are doing and
use common sense. Do not operate tool when
you are tired. Do not rush.
CHECK DAMAGED PARTS. Before further use
of the tool,a guard or other part that isdamaged
shouldbe carefully checked to determine that it
willoperate propedy and perform its intended
function. Check foralignment ofmoving parts,
binding of moving parts, breakage of part.s,
mounting, and any other conditionsthat may
affect its operation. A guard or other part that is
damaged should be properlyrepaired or
replaced by an authorized service center unless
indicated elsewhere in this instruction manual.
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while underthe influence of drugs,
alcohol, or any medication.
DRILLING OR DRIVING SCREWS INTO
ELECTRICAL WIRING IN WALLS, CEILINGS,
OR OTHER AREAS CAN CAUSE THE BIT OR
CHUCK TO BECOME ELECTRICALLY LIVE.
Do not touch metal parts when drillinginto awall;
grasp only the insulated handle(s) or plastic
housingwhen using this tool. Make sure hidden
electrical wiring, water pipes, and mechanical
hazards are notin the path of the bitwhen
ddlling intoa wall.
•INSPECT FOR and removeall nailsfrom lumber
before drilling.
IMPORTANT SAFETY RULES FOR BATTERY
TOOLS
II Battery tools do not haveto be plugged intoan
electrical outlet; therefore, they are always in
operating condition. Be aware of possible
hazards when not using your batterytool or
when changing accessories.
USE ONLY THE CHARGER PROVIDED WITH
YOUR BATrERY TOOL. Do not substitute any
other charger. Use of another charger could
cause batteries toexplode causing possible
serious injury.
[]
DO NOT PLACE BATTERY TOOLS OR THEIR
BATTERIES NEAR FIRE OR HEAT. They may
explode.
DO NOT CHARGE BATTERY TOOL IN A
DAMP OR WET LOCATION.
Your battery toolshould be charged in a location
where the temperature is more than 50°F but
less than 100°F.
Under extreme usage or temperature conditions,
battery leakage may occur. Ifliquid comes in
contact withyour skin,wash immediately with
soap and water, then neutralize with lemon juice
orvinegar. If liquid gets inyour eyes,flush them
withclean water for at least 10 minutes, then
seek immediate medical attention.
If carryingyour battery tool at your side, make
sure it is not running and your finger isnot on the
switch.Avoid accidental starting.
SECURE WORK before applying power. NEVER
holdworkpiece in your hand or across your legs.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS,
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER
SAVE THESE INSTRUCTIONS. This manual
contains important safety and operating
instructionsfor battery charger part number
999555-007.
Before using battery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and productusing battery
charger.
A WARNING: To reduce risk of injury, charge only
nickel-cadmium type rechargeable batteries.
Other types of batteries may burst causing
personal injuryand damage.
Do notexpose charger to rain or snow.
Use of an attachment not recommended or sold
bythe battery charger manufacturer may result
in a risk of fire, electricshock, or injury to
persons.
To reduce riskof damage to charger body and
cord, pull by charger body rather than cordwhen
disconnecting charger.
Make sure cord islocated so that it will not be
stepped on, tripped over, or otherwise subjected
to damage orstress.
4