Blades, Framingsquare, PHiLLiPS, Flathead

BLADES		,_	WARNING: Do not use blades rated less than the
For maximum performance, it is recommended that you
			speed of this tool. Failure to heed this warning could
use the 24-tooth, 10 in. carbide-tipped combination blade
			result in personal injury.
provided with your saw. Additional blade styles of the

same high quality are available for specific operations
such as ripping. Your local dealer can provide you with
complete	information.

Kerr width must be within the limits stamped on the spreader/riving knife.

The following tools (not included or drawn to scale) are needed for assembly and making adjustments:

FRAMINGSQUARE

PHiLLiPS

SCREWDRIVER

FLATHEAD

SCREWDRIVER

SOCKETWRENCH WiTH 10 rnrnAND 11 rnm SOCKET

C-CLAiViP

Fig. 4

Page 13

Image 13

Craftsman 315.28461 manual Blades, Framingsquare, PHiLLiPS, Flathead, Socketwrench WiTH 10 rnrnAND 11 rnm Socket

Contents

Operator MAN AL ONE Year Full Warranty on Craftsman Tool Read ALL Instructions Blade Coasts After Being Turned OFF Adjustments are SecureNever Operate the SAW on the Floor Before Making a CUT, be Sure ALL Material AT a Time Never CUT More than ONE Piece Name SymbolDesig NATION/EXPLANATION Service Symbol Signalmeaning Cord Length Extension CordsElectrical Connection Miter Cut Adjusting Bevel Fence Scale SwitchGuard SPREADER/RIVING Knife Lever See Figure Knowyourtablesaw Switchswitch Switch AssemblySwitchkey Switchin Lockedposition Framingsquare BladesPHiLLiPS Flathead Thefollowingitemsareincludedwiththetablesaw Foot Leg Mounting Holes Unpacking Carriage To Assemble the LEG StandUpper Brace Screw To Install the HandleLever Screws Fence Releaselever UnlockedUP Positionforthroughcutting 0PEN-ENDWRENCH CLOSED=ENDWrench See Figures 14 To Check and Align the SPREADER/RIVING Knife and SAW Blade Pawl Handle Button ANTI=KICKBACK CorrectSee Figures 17 Spreader Rivingknife Framing Sciuare Push Stickstorage To adjust verticallyPush Stick Blade Basic Operation of the Table SAW ApplicationsCauses of Kickback Avoiding Kickback Pushblocks Cuttingaids18-1/2 JIG HOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard Featherboard Push Crosscut TypesofcutsBevelcrosscut Lever HEIGHT/BEVEL Adjusting 900ADJUSTMENT450 AdjustmentLocking Lever HEIGHT/BEVEL Adjusting Gullet Lever RiP Clamp LockingLiP Mark Lock Miterknob To USE the Miter GaugeMiter To USE the Miter Gauge in a Reverse Position See Figures 33 Heeling Paralleling the Blade to the Miter Gauge Groove Making a Cross CUT Switch J SwitchSee Figures 36 Crosscut Placerighthandon Mitergaugehere RIP Bladefence RiPCUTMaking a Miter CUT Mitercut Blade VIEWEDFROMTHEFRONT,BELOWTHETABLESAW Makinga BevelcrosscutTighten Lockinglever Bevelcrosscut Angled Scale BEVELRiPCUT RiPFENCEMaking a Compound Bevel Miter CUT Placelefthandonmiter Gaugehere Bladeguard Making a NON=THROUGH CUTRemoved See Figures 45 To Replace the BladeClosedend Wrench Arborblade Shaftwasher Indicator Adjustment ScrewSee Figures 48 Handle To Check the Alignment of the RiP Fence to the Blade General MaintenanceBolts Lubrication Cause Solution SOLUTIONi Problem See FigureD Description QTY KEY Part NO. NumberKEY Part NO. Number Description KEY Part NO. Number Description Parts List for Figure a See Figure C Model Number in all correspondence regarding your Number KEY Part Number Description Part Descri Ption Parts List for Figure D Number Description Description QTY

BLADES

FRAMINGSQUARE

PHiLLiPS

FLATHEAD

SOCKETWRENCH WiTH 10 rnrnAND 11 rnm SOCKET