Craftsman 315.28461 manual Blade Coasts After Being Turned OFF, Never Operate the SAW on the Floor

[] KEEP HANDS AWAY FROM CUTTING AREA. Keep hands away from blades. Do not reach underneath work or around or over the blade while blade is rotating. Do not attempt to remove cut material when blade is moving.

[] BLADE COASTS AFTER BEING TURNED OFF.

[] NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes.

[] INSPECT TOOL CORDS PERIODICALLY. if damaged, have repaired by a qualified service technician at

an authorized service facility. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor, if repair or replacement of the electric cord or plug is necessary, do not connect the equipment- grounding conductor to a live terminal. Repair or replace a damaged or worn cord immediately. Stay constantly aware of cord location and keep it well away from the rotating blade.

[] iNSPECT EXTENSION CORDS PERiODiCALLY and replace if damaged.

[] GROUND ALL TOOLS. If tool is equipped with three- prong plug, it should be plugged into a three-hole electrical receptacle.

[] CHECK WiTH A QUALiFiED ELECTRiCiAN or service personnel if the grounding instructions are not completely understood or if in doubt as to whether the tool is properly grounded.

[] USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug.

[] DO NOT MODIFY the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician.

[] KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when

[] FIRMLY BOLT THE SAW TO A WORK BENCH OR LEG STAND at approximately hip height.

[] NEVER OPERATE THE SAW ON THE FLOOR.

[] GUARD AGAINST KICKBACK. Kickback occurs when the blade stalls rapidly and workpiece is driven back towards the operator. It can pull your hand into the blade resulting in serious personal injury. Stay out

of blade path and turn switch off immediately if blade binds or stalls.

[] USE RIP FENCE. Always use a fence or straight edge guide when ripping.

cleaning. Never use brake fluids, gasoline, petroleum- based products, or any solvents to clean tool.

[] STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush.

[] DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

[] USE ONLY CORRECT BLADES. Do not use blades with incorrect size holes. Never use blade washers or blade bolts that are defective or incorrect. The maximum blade capacity of your saw is 10 in. (254 mm).

[] BEFORE MAKING A CUT, BE SURE ALL

ADJUSTMENTS ARE SECURE.

[] BE SURE BLADE PATH IS FREE OF NAILS. Inspect

for and remove all nails from lumber before cutting.

[] NEVER TOUCH BLADE or other moving parts during use.

[] NEVER START A TOOL WHEN ANY ROTATING COMPONENT IS IN CONTACT WITH THE WORKPIEOE.

[] DO NOT OPERATE A TOOL WHILE UNDER THE

INFLUENCE OF DRUGS, ALCOHOL, OR ANY MEDICATION.

[] WHEN SERVICING use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.

[] USE ONLY RECOMMENDED ACCESSORIES listed in this manual or addendums. Use of accessories that

are not listed may cause the risk of personal injury. Instructions for safe use of accessories are included

with the accessory.

[] DOUBLE CHECK ALL SETUPS. Make sure blade is tight and not making contact with saw or workpiece before connecting to power supply.

[] SUPPORT LARGE PANELS. To minimize risk of blade pinching and kickback, always support large panels.

[] REMOVE ALL FENCES AND AUXILIARY TABLES before transporting saw. Failure to do so can result in an accident causing possible serious personal injury.

[] ALWAYS USE BLADE GUARD, SPREADER, AND ANTI-KICKBACK PAWLS on all "through-sawing" operations. Through-sawing operations are those in which the blade cuts completely through the workpiece as in ripping or cross cutting. Keep the blade guard down, the anti-kickback pawls down, and the spreader in place.