TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from tile power source before performing all of the recommended remedies below except remedies that re- quire unit to be operating.
TROUBLE |
|
| CAUSE |
|
|
|
|
| REMEDY |
|
|
|
|
| |||||
Trimmer |
| head | 1. | Crowdh_g trimmer Ih_e | 1. | Allow tip of line to do the cutting. | |||||||||||||
stops under | a |
| against |
| material | being |
|
|
|
|
|
|
|
| |||||
load | or | does | not |
| cut. |
|
|
|
|
|
|
|
|
|
|
|
|
| |
turn | when | switch | 2. | Electrical | failure. | 2. | Contact | Sears Service | (see back | ||||||||||
is pressed. |
|
|
|
|
|
|
|
|
| cover). |
|
|
|
|
|
| |||
|
|
|
|
| 3. | Thrown |
| circuit | breaker. | 3. | Check |
| Breaker | Box. |
|
| |||
|
|
|
|
| 4. | Debris | stopping | head. | 4. | Remove | debris. |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
Line | does | not | 1. | Line | improperly | routed | 1. | Check |
| line | routing. |
|
| ||||||
advance |
| or |
|
| in head. |
|
|
|
|
|
|
|
|
|
|
|
| ||
breaks | while |
| 2. | Line | improperly |
| 2. | Rewind |
| line | tightly and | evenly. | |||||||
|
|
|
|
|
|
| |||||||||||||
cutting. |
|
|
|
| wound | into spool. |
|
|
|
|
|
|
|
| |||||
|
|
|
|
| 3. | Incorrect | line size | 3. | Use only 0.065 | inch | (1.65 mm) dia. line. | ||||||||
|
|
|
|
| 4. | Not | enough | line | 4. | Remove | cover | and | pull | 4 inches | |||||
|
|
|
|
|
| outside |
| of head. |
| (10 cm) | of line out of head. | ||||||||
|
|
|
|
| 5. | Dirt | buildup | on | unit. | 5. | Clean | unit. |
|
|
|
| |||
Line | welds onto | 1. | Line | size is | incorrect. | 1. | Use only 0.065 inch (1.65 mm) dia. line. | ||||||||||||
spool. |
|
|
| 2. | Incorrect | spool. |
| 2. | Replace | with | correct | spool. | |||||||
|
|
|
|
| 3. | Line | is being | crowded | 3. | Cut with tip | of | line fully | extended. | ||||||
|
|
|
|
|
| against |
| material | being |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| cut. |
|
|
|
|
|
|
|
|
|
|
|
|
|
Line releases continuously.
Line usage is excessive.
Line pulls back into head.
1.Line improperly routed in head.
2.Spool damaged.
1.Line improperly routed in head.
2.Line size is incorrect.
3.Crowding line against material being cut.
4.Spool worn or damaged.
1.Too little line outside of head.
2.Line size incorrect.
1.Check line routing.
2.Replace spool.
1.Check line routing.
2.Replace spool.
3.Cut with tip of line fully extended.
4.Replace spool.
1.Remove cover and pull 4 inches (10 cm) of line outside of head.
2.Use only 0.065 inch (1.65 mm) dia. line.
10
