29
SERVICE AND ADJUSTMENTS
CAUTION: Beforeservicingoradjusting
thesnowthrower,shutofftheengine,remove
the spark plug wire(s), set the parking brake
andremovethekeyfromthetractorignition.
FIGURE 65
FIGURE 64

REPLACING AUGER BELT

• Disengagethetractor'sattachmentclutch.
• Lowerthesnowthrowertotheground.
• Removetheattachmentpin.
• Lockthesnowthrower'slifthandleinthedown
position to decrease belt tension.
• Releasethespringtensionfromtheaugerbeltidler
arm on the bottom of the clutch/idler assembly.
• Removetheaugerdrivebeltfromtheclutch/idler
assembly and from the spiral auger housing.
• Installnewbeltovertopoflargeaugerdrivepulley
and under the two side idler pulleys. Twist the belt 1/4
turntoseatthe"V"ofthebeltinthegrooveofeach
idler pulley. Refer to gure55onpage23.
• Assemblethebeltontotheclutch/idlerassembly.

SKID SHOE ADJUSTMENT

• Theskidshoesaremountedoneachsideofthespiral
auger housing. They regulate the distance the scraper
plateisraisedabovetheplowingsurface.When
removingsnowfromagraveldrivewayoranduneven
surface,itisadvisabletokeepthescraperplateas
highabovethesurfaceaspossibletopreventpossible
damage to the spiral auger. On blacktop or concrete
surface, keep the scraper plate as close to the surface
as possible.
• Raisethesnowthroweroffthegroundandplacea
block under each end of the scraper plate. Loosen the
six hex nuts securing the skid shoes to the housing.
Adjust the skid shoes up or down and retighten the
nuts securely. Adjust both skid shoes to the same
heighttokeepthehousingandthescraperplatelevel.
Seegure64.

LIFT RELEASE CABLE ADJUSTMENT

• Iftheliftroddoesnotlockthesnowthrowersecurely
in the transport position, loosen the upper hex nut on
the lift bracket a few turns and tighten the lower hex
nut.Refertogure48onpage21.
• Iftheliftrodfailstounlockcompletelytolowerthe
snow thrower, loosen the lower hex nut on the lift
bracket a few turns and tighten the upper hex nut.
Refertogure48onpage21.

CLUTCH DISENGAGEMENT ADJUSTMENT

(For tractors with engagement rod clutches only.
Not for electric clutches or cable clutches)
If the spiral auger on the snow thrower does not stop
whentheattachmentclutchleveronthetractoris
disengaged, then adjustment is necessary. Proceed as
follows.Referbacktogure33onpage16.
• Placetheattachmentclutchleverinthedisengaged
position.
• Removethehairpincotterfromtheengagementrod
trunnion and lift the trunnion out of the hole in the idler
arm.
• Screwthetrunnionafewturnstowardsthefrontend
of the rod.
• Replacethetrunnionintotheholeintheidlerarmand
secure it with the hairpin cotter.
Check the operation of the snow thrower. If the spiral
augersstilldonotstop,repeattheabovestepsuntil
theaugersstopwhentheattachmentclutchleveris
placed in the disengaged position.

SPIRAL AUGERS

• Thespiralaugersaresecuredtotheaugershaftwith
two shear bolts and nylock nuts. If you hit a foreign
object or if ice jams the augers, the snow thrower is
designed so that the bolts will shear.
• Iftheaugerswillnotturn,checktoseeiftheshear
boltshavesheared.Seegure65.Tworeplacement
shearboltsandnylocknutshavebeenprovidedwith
the snow thrower. For future use order part number
710-0890A shear bolt and number 47810 nylock nut.