Panasonic DW10000U, PT-D10000U Raster position

ENGLISH – 65

Basic Operation

Note

When “FRAME DELAY” is set to “SHORT”,

deterioration in the picture quality will occur.

Furthermore, the noise reduction function cannot be

used.

Raster position

When the whole area where the input picture can be

displayed is not used, the picture can be moved to

any position inside the display area.

1. Press ▲▼ to select “RASTER

POSITION”.

2. Press ENTER.

The “RASTER POSITION” screen will be

displayed.

3. Press ▲▼◄► to adjust the

position.

PT-D10000U

•

•

■

ADVANCED MENU

DIGITAL CINEMA REALITY

BLANKING

INPUT RESOLUTION

CLAMP POSITION

EDGE BLENDING

FRAME DELAY

RASTER POSITION

MENU SELECT

SUB MENU

AUTO

OFF

DEFAULT

ENTER

ADVANCED MENU

DIGITAL CINEMA REALITY

BLANKING

INPUT RESOLUTION

CLAMP POSITION

EDGE BLENDING

FRAME DELAY

RASTER POSITION

MENU SELECT

SUB MENU

AUTO

OFF

DEFAULT

ENTER

RASTER POSITION

V

H

ADJUST

0

0

RASTER POSITION

V

H

ADJUST

0

0

When 5:4 pictures are displayed

(when SXGA signals are input)

Pressing ► button will move

the image to the right.

Pressing ◄ button will move

the image to the left.

When 5:4 pictures are displayed

(when SXGA signals are input)

Pressing ► button will move

the image to the right.

Pressing ◄ button will move

the image to the left.

PT-DW10000U

4. Press MENU three times.

The on-screen indications disappear and the

normal screen appears again.

■

•

When 16:9 pictures are displayed

(when HDTV or 480p pictures are input or

16:9 is selected in the SIZE mode)

Pressing ▲ button will move

the image upward.

Pressing ▼ button will move

the image downward.

When 16:9 pictures are displayed

(when HDTV or 480p pictures are input or

16:9 is selected in the SIZE mode)

Pressing ▲ button will move

the image upward.

Pressing ▼ button will move

the image downward.

When 4:3 pictures are displayed

Pressing ► button will move

the image to the right.

Pressing ◄ button will move

the image to the left.

When 4:3 pictures are displayed

Pressing ► button will move

the image to the right.

Pressing ◄ button will move

the image to the left.

Contents

Main Dear Panasonic Customer: Getting StartedGetting Started Basic OperationSpecial FeaturesInformation Contents IMPORTANT SAFETY NOTICE Page 6 Precautions with regard to safety WARNING Page Page Page Before Using 10 Accessories Caution when moving the projector Cautions regarding setup Notes on use To view clear images: Do not touch the surface of the projection lens with bare hand. Screen Lamp Location and function of each part Front Remote control unit SideTop Bottom 14 Projector Main Unit Front Location and function of each part (continued) Rear ControlsSide Location and function of each part (continued) Connection terminals Using the remote control unit Loading batteries 1. Open battery compartment lid. 2. Insert the batteries. 3. Close the battery compartment lid. 18 Using the remote control unit (continued) Setting projector ID number to remote control Using a wired remote control Installation 20 Installation (continued) Adjusting the feet Projection scheme Installation geometry Projection distances by the type of projection lenses (optional) Projection distances by the type of projection lenses (for PT-DW10000U) For the screen aspect ratio of 16:9 (Units: m (feet/inches)) L : Projection distance SH : Effective screen height SW : Effective screen width Side View Projection distances by the type of projection lenses (for PT-D10000U) Installation (continued) For the screen aspect ratio of 4:3 (Units: m (feet/inches)) For the screen aspect ratio of 16:9 (Units: m (feet/inches)) Lens type Zoom lens Fixed-focus Calculation formulas for projection distance by lens types (for PT-DW10000U) Calculation formulas for projection distance by lens types (for PT-D10000U) Connection 24 Before starting connection The pin-out and signal names of the DVI-D IN terminal are shown in the diagram below. The pin-out and signal names of the S-VIDEO IN terminal are shown in the diagram below. Example of connecting with VIDEO devices 26 Connection (continued) Example of connecting with personal computers Installation of input module (optional) Installing the input module Types of the input modules (optional) Prepare beforehand an input module (optional) compatible with the input signals of the system. Module Module model No. Terminal Signal formats supported Procedure of installation 1. Remove the slot cover. 2. Insert the input module. 3. Fix the input module. 4. Register the input signal. 1. Remove the slot cover. Connecting signals to the input module 30 Connecting the signal to the SD-SDI input module Connecting the signal to the HD/SD-SDI input module 32 Connecting signals to the DVI-D input module How to install and remove the projection lens (optional) How to install the projection lens How to remove the projection lens 34 Projection Power indicator lamp Connecting the power cord Powering up the projector Making adjustment and selection 36 Powering off the projector How to adjust the lens How to adjust the focus, zoom and shift CAUTION: At the projector 1. Press LENS on the control panel on the main unit. 2. Press to select an item and adjust it. 38 How to adjust the lens (continued) Adjustment range after lens position (optical shift) The ET-D75LE5 has a fixed focal point, and so shift adjustment cannot be carried out. Moving the projection lens position to the home position Automatic adjustment (AUTO SETUP) a 40 Registration of input signal data Registration of new data Renaming the registered signals 1. Press to select the signal whose details are to be displayed. 4. Use to select the characters and numerals one by one, and press ENTER to set them. Clearing the data of registered signals 1. Press to select the signal whose data is to be cleared. 2. Press DEFAULT. Sub memory How to register into sub memory 2. Press to select the SUB MEMORY number stored in the SUB MEMORY LIST. Registration of input signal data (continued) Procedure to switch to sub memory 1. Press on normal screen (menu is not displayed). 2. Press to select the sub-memory signal to be switched in the SUB MEMORY LIST. How to erase sub memory Basic operations using the remote control 44 Remote control operation (continued) Automatic adjustment (AUTO SETUP) 1. Press AUTO SETUP on the remote control or the main unit. Turning on button illumination Changing the picture aspect ratio 1. Press ASPECT on the remote On-screen menus 46 MAIN MENU SUB MENU PICTURE (pp. 49-55) POSITION (pp. 56-59) ADVANCED MENU (pp. 60-65) SECURITY (pp. 99-101) OPTION1 (pp. 67-74) DISPLAY LANGUAGE (p. 66) Adjusting the picture 50 Adjusting Contrast Press to select BRIGHTNESS. 1. This adjusts the contrast for picture colors. Adjusting Tint This adjusts skin tones in the pictures. 1. Press to select TINT. The TINT individual adjustment screen will be Adjusting the color temperature 52 8. Press to adjust the level. 1. Press to select GAMMA. Gamma setting This switches the gamma mode. Noise reduction setting 63 (High) 262 (Intermediate) 1. Press to select NOISE REDUCTION. 2. Press to switch NOISE REDUCTION. The setting will change as follows each time 54 Registering the picture mode settings as presettings 1. Press ENTER. 2 Press to select OK. Setting the system format To display pictures complying with the sRGB standard RGB YP Adjusting the position 56 Shift adjustment 3. 1. Press to select SHIFT. Adjusting the aspect ratio 1. Press to select ASPECT. 2. Press to switch ASPECT. 58 Adjusting the position (continued) Adjusting the zoom ratio 1. Press to select ZOOM. 3. Press to select MODE. 4. Press to switch MODE. Keystone distortion correction 1. Press to select KEYSTONE. 3. Press to adjust the KEYSTONE. 60 Digital cinema reality How to use ADVANCED MENU Blanking adjustment 1. 3. Press to select BLANKING. 62 How to use ADVANCED MENU (continued) Adjusting the clamp position 1. Press to select CLAMP 3. Press to adjust. 4. Press to specify the area to be adjusted. 14 13 11 10 64 How to use ADVANCED MENU (continued) 15 18 17 Raster position 1. Press to select RASTER 3. Press to adjust the position. PT-D10000U PT-DW10000U 4. Press MENU three times. Setting the DISPLAY LANGUAGE Changing the display language 1. Press to select the desired language. 2. Press ENTER to establish your selection. Option1 settings Special Features Basic Operation Adjusting color matching 1. Press to select COLOR 2. Press to switch COLOR 68 If 3COLORS or 7COLORS was selected in step 2. The MEASURED DATA screen will be displayed. The COLOR MATCHING: 3COLORS or COLOR MATCHING: 7COLORS screen will 4. Press to select R, G and B. Large Screen Correction 1. Press to select LARGE SCREEN CORRECTION. 2. Press to switch LARGE SCREEN CORRECTION. The setting will change as follows each time 70 Auto signal 1. Press to select AUTO SIGNAL. 2. Press to switch AUTO SIGNAL. Automatic adjustment (Only RGB input) Back Color 1. Press to select BACK COLOR. 2. Press to switch BACK COLOR. DVI EDID 1. Press to select DVI EDID. 72 AUX DVI EDID (Only when the optional input module is installed) 1. Press to select AUX DVI EDID. 2. Press to switch AUX DVI EDID. Setting FUNC1 1. Press to select FUNC1. 2. Press to switch FUNC1. 74 Position of on-screen indications OFF ON The user can specify the position of the on-screen indications. 1. Press to select OSD Option2 settings 76 Installation Setting 1. Press to select INSTALLATION. 2. Press to switch INSTALLATION. 3. Press MENU twice. Direction 1. Press to select DIRECTION. 2. Press to switch DIRECTION. Output resolution (PT-D10000U only) 1. Press to select OUTPUT 78 Lamp select 1. Press to select LAMP SELECT. 2. Press to switch LAMP SELECT. Lamp relay 5. Press 1. Press to select LAMP RELAY. 2. Press to switch LAMP RELAY. OFF 00:00 23:00 01:00 80 System information Displays the system information of the projector. 1. Press to select SYSTEM INFORMATION. The SYSTEM INFORMATION screen will be Setting the date and time 1. Press to select DATE AND TIME. 3. Press to select TIME ZONE. 4. Press to switch TIME ZONE. 5. Press to select ADJUST CLOCK. 82 Setting the startup logo 1. Press to select STARTUP LOGO. 2. Press to switch STARTUP LOGO. Password Displaying the internal test pattern Test pattern How to use network function 84 Initial setting of network 1. Press to select items, and press ENTER to change the setting. 2. Press to select STORE, and press ENTER. Returning the network function setting back to the factory setting 1. Press to select STORE. 2. Hold down DEFAULT for 3 seconds. 86 Network connections Name and function of network function parts Accessing from the Web browser 4. Press OK and the top page will appear. Password change page Basic control page Detail control page Monitor information page Error information page When [FAILED] has appeared for an item OK: Normal operation FAILED: Occurrence of trouble OK: Normal operation FAILED: Occurrence of trouble Parameter Description Parameter Description E-mail setup page E-mail setup page (continued) DNS server set up page Authentication server setting page Ping test page Contents of mail sent Mail with the contents shown below is sent when the E-mail settings have been established. Mail with the contents shown below is sent when an error has occurred. Adjust clock page Network config page Firmware update page Using the PJLink protocol 98 Supported commands The following table lists the PJLink protocol commands that can be used to control the projector. PJLink security authorization Setting the security Displaying the security screen If using for the first time 1. Press , , , , , , and in this order. If the existing password has been changed 100 Setting the security (continued) 2. Press to switch PASSWORD. Changing the password 1. Press to select PASSWORD CHANGE. Changing the text 1. Press to select TEXT CHANGE. The TEXT screen will be displayed. 3. Press to select the text position, and press to select the characters of the text. The text is now changed. Using the serial terminals 102 Examples of connection Communication conditions (Factory setting) For RS-232C For RS-422 Single projector Communication conditions (Factory setting) Plural projectors Pin assignments and signal names 104 Using the serial terminals (continued) Basic format Control commands Cable specifications Connecting to a PC For RS-232C When multiple projectors are connected Using the Remote 2 terminal 106 Example of a control panel layout Pin assignments and control Indication of monitor lamp LAMP 4 monitor (LAMP 4) LAMP 2 monitor (LAMP 2) LAMP 1 monitor (LAMP 1) LAMP 3 monitor (LAMP 3) Temperature monitor (TEMP) LAMP 4 monitor (LAMP 4) LAMP 2 monitor (LAMP 2) Cleaning and replacement of air filter Procedure of cleaning Page Replacement of lamp unit 110 Precautions on lamp unit replacement Timing of lamp unit replacement Indication after 1 800 hours Procedure of lamp unit replacement 112 Notes when installing the ceiling mount bracket Installation procedure Before asking for service Self-diagnosis display Self- diagnosis display Details Remedy Specifications Model No. PT-D10000U PT-DW10000U Appendix 118 Compatible RGB/YPBPR/DVI-D Signals Display mode Number of displayed dots Scanning frequency Dot clock frequency (MHz) Format H (kHz) V (kHz) List of P IN P Subwindow Main window 120 Dimensions Outside dimensions Installation dimensions diagram Index A B C D Trademark Acknowledgement Note: NOTES IMPORTANTES CONCERNANT LA SCURIT 124 Prcautions de scurit AVERTISSEMENT Page Page Page 128 Avant lutilisation Accessoires Mise en garde concernant les dplacements du projecteur Mises en garde concernant la configuration Remarques concernant lutilisation Pour voir des images trop claires : Ne jamais toucher la surface de lobjectif de projection avec les mains nues. cran Lampe Remplacement de la lampe 130 Prcautions prendre lors du remplacement de la lampe Intervalle de remplacement de la lampe Indication aprs 1800 heures Procdure de remplacement de la lampe