How to use Advanced Menu, Auto | Panasonic DW10000U, PT-D10000U

How to use ADVANCED MENU

MENU

▲▼◄►

ENTER

Fine settings are possible.

MENU	Press to display the
	Press to display the
	MAIN MENU screen.
	Press to select
	“ADVANCED MENU”.
	Press to display the
	“ADVANCED MENU”
	menu.

MAIN MENU

PICTURE

POSITION

ADVANCED MENU

DISPLAY LANGUAGE

OPTION1

OPTION2

TEST PATTERN

SIGNAL LIST

NETWORK

SECURITY

MENU SELECT

ENTER SUB MENU

Digital cinema reality

Increase the vertical resolution when the PAL (or SECAM) 576i signal input or the NTSC 480i, 1 080/50i and 1 080/60i signal input is applied.

1.Press ▲▼ to select “DIGITAL CINEMA REALITY”.

ADVANCED MENU

DIGITAL CINEMA REALITY	AUTO
BLANKING
INPUT RESOLUTION
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING	OFF
EDGE BLENDING	OFF
FRAME DELAY	DEFAULT
RASTER POSITION

MENU SELECT

CHANGE

2.Press ◄► to switch “DIGITAL CINEMA REALITY”.

•The setting will change as follows each time ◄► is pressed.

	AUTO		OFF
	AUTO		OFF

30p FIXED: When 480i or 1 080/60i signals are input

25p FIXED: When 576i or 1 080/50i signals are input

•AUTO:

Performs automatic detection and cinema processing. (factory default)

•OFF:

Unforced cinema processing

•25p FIXED:

Forced cinema processing (2:2 pulldown) is performed when a 576i or 1 080/50i signal is input.

•30p FIXED:

Forced cinema processing (2:2 pulldown) is performed when a 480i or 1 080/60i signal is input.

Note

•In DIGITAL CINEMA REALITY mode, the image quality will be deteriorated if 30p FIXED or 25p FIXED is selected when the signal is not a 2:2 pulldown signal.

60 – ENGLISH

Image 60

Panasonic DW10000U manual How to use Advanced Menu, Digital cinema reality, Press to switch Digital Cinema Reality, Auto

Contents

PT-DW10000U Models No. PT-D10000U Dear Panasonic Customer Model number PT-D10000U/PT-DW10000USerial number Contents Important Safety Notice Getting Started Panasonic Precautions with regard to safety Do not handle the power cord plug with wet handsDo not overload the wall outlet Do not remove the cover or modify it in any way Insert the power cord plug securely into the wall outlet Insulate the battery using tape or similar before disposalDo not place the projector into water or let it become wet Do not disassemble the lamp unit Use only the specified battery Always disconnect all cables before moving the projectorDo not place any heavy objects on top of the projector Do not look into the lens while the projector is being used Electric shocks can result if this is not done Before Using AccessoriesDo not place the projector on a vinyl sheet or carpet Otherwise the life of the product may be shortened Maintenance DisposalTo view clear images Screen Remote control unit Location and function of each partFront Remote control transmitter window Side Top BottomMenu Lock button Projector Main Unit RearLamp LAMP1, LAMP2, LAMP3, LAMP4 Power Standby SideControls Connection terminals Using the remote control unit Effective range of remote control operationLoading batteries Setting projector ID number to remote control Using a wired remote control Installation Examples of system expansion Adjusting the feet Installation geometryProjection scheme Started GettingSide View Top View For the screen aspect ratio of 43 Units m feet/inches Zoom Pin Signal ConnectionBefore starting connection Outside view Pin No Example of connecting with Video devices Control PC Video deck TBC built-in Example of connecting with personal computers Control PC To 2nd projector Serial in terminalControl PC Installation of input module optional Installing the input moduleModule Module model Terminal Signal formats supported Types of the input modules optional Procedure of installation Fix the input module Register the input signalRemove the slot cover Insert the input module Connecting signals to the input module Connecting the signal to the SD-SDI input module SD-SDI input module optionalBusiness digital VCR Connecting the signal to the HD/SD-SDI input module HD-SDI or SD-SDI Signal Signal output Active throughHD/SD-SDI input module optional ET-MD77SD3 for HD/SD LAN terminal *1 Connecting signals to the DVI-D input module DVI-D input module optional# + How to install the projection lens How to remove the projection lensProjection lens cover lock button Projection lens lock button Mark orange Power indicator lamp Connecting the power cordInstallation Indicator Projector status Status Powering up the projector Making adjustment and selectionPress Power on # $ Powering off the projector # Press Power StandbyConfirmation screen will appear How to adjust the lens How to adjust the focus, zoom and shift Adjustment range after lens position optical shift Moving the projection lens position to the home positionModel number PT-D10000U PT-DW10000U Projection lens Automatic adjustment Auto Setup How to adjust the lens for addressing unevenness of focusing Registration of input signal data Registration of new dataPress Enter Press to display Clearing the data of registered signals Sub memoryEnter Procedure to switch to sub memory How to erase sub memorySUB Memory List On-screen indications Switching the input signal Basic Operation Using the Shutter functionOn-screen display function Status function Automatic adjustment Using the FUNC1 buttonTurning on button illumination Displaying the internal test pattern Press Aspect on the remote control Setting will change as follows each time Aspect is pressedChanging the picture aspect ratio On-screen menus Picture ppIcon Main Menu item SUB Menu item Test Pattern p Signal List pp Network pp Position ppAdvanced Menu pp Display Language p Using the menu screens Resetting to the factory default Adjusting the picture Switching the picture modePress to select Picture Mode Press to switch Picture Mode Adjusting Contrast Adjusting BrightnessAdjusting Color Adjusting Tint Adjusting the color temperature Gamma setting Sharpness settingThis adjusts the sharpness of the pictures This switches the gamma mode Noise reduction setting Dynamic iris setting Setting the system format RGB1/RGB2/DVI-D terminal input signals Display the Picture screen. p Press to select Picture ModeSRGB is only enable when RGB signals are being input Press to select Natural Press to select Color Adjusting the position Shift adjustmentFor horizontal right and left adjustment Press to select Shift Adjusting the aspect ratio Press to switch AspectOperation Basic Adjusting the zoom ratio Clock phase adjustmentInterlocked Press to adjust the Keystone Keystonedistortion correctionKeystone screen will be displayed Value changes from -127 to How to use Advanced Menu Press to switch Digital Cinema RealityDigital cinema reality Advanced Menu Blanking adjustment Press to select Input ResolutionPress to select Blanking Adjusting the clamp position Edge blending adjustmentBlending Press to specify the area to be adjusted Press to select Bright AdjustPress Enter to select on Press to select Bright Inside Press Enter Frame delay Press to select Frame DelayPress to switch Frame Delay Press to adjust the position PT-D10000U Raster positionPress to select Raster Position PT-DW10000U Setting the Display Language Changing the display languagePress to select the desired language Language Option1 settings Adjusting color matchingBasic Operation Special Features Press to switch Color Matching Using a colorimeter MatchingData Large Screen Correction Press to select R, G, B or Cy, Mg, Ye, Wh Press EnterTarget Data screen will be displayed Auto signal Automatic adjustment Only RGB inputSignal Press to switch Back Color Back ColorPress to select Back Color Press to select DVI Edid Press to switch AUX DVI Press to switch P in PPress to select AUX DVI Edid Edid Setting FUNC1 Press to switch FUNC1Press to select FUNC1 Position of on-screen indications OSD memory Option2 settings Setting a projector IDPress Menu twice Press to select OPTION2 Press to display the OPTION2 menu Installation Setting AltitudePress to select Altitude Output resolution PT-D10000U only Press to select Output ResolutionResolution Direction Press to switch Lamp Select Lamp selectPress to select Lamp Select RS-232C setting Lamp relay System information Cleaning the air filter Setting the date and time Adjust Clock screen will be displayedThis completes setting of the time Press to select Date and Time Setting the startup logo Password Press to switch Startup LogoPress to select Startup Logo Displaying the internal test pattern Test patternCycle of displayed internal test Patterns Pattern How to use network function Initial setting of network functionPress to select STORE, and press Enter Hold down Default for 3 seconds Press to select Store Network connections Name and function of network function partsOr sent Accessing from the Web browser Press OK and the top page will appear Password changeClick Change password Basic control Lens adjustment Test pattern display Detail controlMonitor information Menu display Error information When Failed has appeared for an item Mail setup English DNS server set up Button to update settingsFeaturesSpecial Numbers 0 9, period Authentication server setting Ping test Contents of mail sent Adjust clock Network config Firmware update Using the PJLink protocol Supported commandsPJLink security authorization Command Control details Setting the security Setting the passwordEnter the new password Displaying the security screen Setting the text Changing the passwordPassword Password Change Changing the text Press to select Text ChangeText screen will be displayed Text is now changed Using the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connection Pin Signal Description No. name Signal level RS-422-compliantFor RS-422 Connection terminals Control commands Command Function of command RemarksBasic format Accepted Cable specifications Projector Computer DTE Specifications1st 2nd RS-422 OUT Using the Remote 2 terminal Example of a control panel layoutPin assignments and control Names of terminals Open H Short L Indication of monitor lamp Lamp 1 monitor LampLamp 3 monitor Lamp Cleaning and replacement of air filter Procedure of cleaningPlace the filter cleaning unit Use a vacuum cleaner to remove any dust blockages Install the movable metal mesh Filter to the filter cleaning unitInstall the brush cover so that it Replacement of lamp unit Precautions on lamp unit replacementTiming of lamp unit replacement Indication after 1 800 hours Procedure of lamp unit replacement You might get burned if you touch it while it is still hot Installation procedure WireEye bolt Eye bolt Symptoms Check point Power does not turn onRemote control does not No image appears on screen Self-diagnosis display Self Details Remedy Diagnosis Display FE1 Specifications Model No PT-D10000U PT-DW10000U RGB2 input Compatible RGB/YPBPR/DVI-D Signals Appendix List of P in P Main window Dimensions Outside dimensionsInstallation dimensions diagram Unit mm inch Adjusting color matching Index Trademark Acknowledgement Français Précautions de sécurité Ne pas surcharger la prise du secteurNe pas retirer le capot ou le modifier Cela peut entraîner des chocs électriques Ne pas placer le projecteur sur des surfaces instables Ne jamais démonter la lampeNe pas mettre d’objets étrangers dans le projecteur Ne pas placer plusieurs kits les uns sur les autres Mise en garde Ne pas placer d’objets lourds sur le projecteur’utiliser que le type de piles spécifié Ne jamais réutiliser une lampe usagée Information Accessoires Mise en garde concernant les déplacements du projecteurMises en garde concernant la configuration Avant l’utilisation Mise au rebut Entretien 130 Procédure de remplacement de la lampe Dévisser, à l’aide d’un tournevisMise EN Garde Vis du couvercle de la lampe Panasonic Projector Systems Company Technical SupportPanasonic Canada Inc