Craftsman 79480 manual Rocker Arms Intake, Exhaust, Replacing the Spark Plug, Cleaning

Ad N uts

Rocker Arms INTAKE

EXHAUST

Feeler Gauge

Spark Plug Hole

Fig. 33

Adjusting Nut _,

Rocker Arm

.003-.006 in.

(.076-.152 mm)

Intake Valve

Stem3auge

Valve Stem

Fig. 34

b. Recheck both clearances, and adjust as necessary.

9.Reinstall the rocker arm cover using a new gasket. Torque the screw to 20-30 in°lb (2.2-3.4 N°m).

10.Check the spark plug and reinstall. See Replacing the Spark Plug.

11.Replace the spark plug wire.

12.Reinstall the engine cover. Check alignment of the cover before tightening the screws. Tighten screws.

REPLACING THE SPARK PLUG

electrodesWARNING:. Grit in the engine could damage the cylinder. I Do not sand blast, scrape or clean

Use a Champion RDZ19H or a replacement part number 753-05255 spark plug. The correct air gap is 0.025 in. (0.635 mm.). Remove the plug after every 25 hours of operation and check its condition.

1.Stop the engine and allow it to cool. Remove the eight (8) screws on the back of the engine cover with a Flat-head or T- 25 Torx screwdriver (Fig. 31).

If using a torque wrench torque to: 110-120 in.*lb. (12.3-13.5 N°m) Do not over tighten.

SPARK ARRESTOR MAINTENANCE

Inspect the spark arrestor after every 50 hours of operation.

1.Remove the rear engine cover. See Rocker Arm Clearance.

2.With a flat blade screwdriver, or a Torx T-20 bit and a T-25 bit, remove the 2 screws attaching the spark arrestor cover to the muffler (Fig. 36).

Muffler _____		T-25 Screw
Spark Arrestor Screen
Spark Arrestor Cover	__<_	T-20 Screw
	Fig. 36

3.Pull the tab on the spark arrestor cover out of the muffler. Remove the spark arrestor cover.

4, Remove the spark arrestor screen from the spark arrestor cover.

5.Clean the spark arrestor screen with a wire brush or replace it.

6.Reinstall the spark arrestor screen, spark arrestor cover, and screws.

CLEANING

	turn your unit off and allow it to cool before you clean
I ,_	I WARNING:or service it. To avoid serious personal injury, always

Use a small brush to clean off the outside of the unit. Do not use

strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic housing or handle. Wipe off any moisture with a soft cloth.

STO RAG E

•Never store the unit with fuel in the tank where fumes may reach an open flame or spark.

•Allow the engine to cool before storing.

•Lock up the unit to prevent unauthorized use or damage.

•Store the unit in a dry, well-ventilated area.

•Store the unit out of the reach of children.

LONG TERM STORAGE

1.Drain all gasoline from the gas tank into a container. Do not use gas that has been stored for more than 60 days. Dispose of the old gasoline in accordance to Federal, State, and Local regulations.

2.Start the engine and allow it to run until it stalls. This ensures that all gasoline has been drained from the carburetor.

3.Allow the engine to cool. Remove the seven (7) screws on the back of the engine cover with a Flat-head or T-25 Torx screwdriver. Remove the spark plug and put 5 drops of high quality motor oil into the cylinder. Pull the starter rope slowly to distribute the oil. Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the oil from the cylinder before attempting to start the blower after storage.

2.Grasp the plug wire firmly and pull the cap from the spark plug.

3.Clean dirt from around the spark plug. Remove the spark plug from the cylinder head by turning a 5/8 in. socket counterclockwise.

4.Replace cracked, fouled or dirty spark plug. Set the air gap at 0.025 in. (0.635 mm.) using a feeler gauge (Fig. 35).

0.025 in.

(0.635 mm.)

I.

T

A

T

4.Change the oil, referring to Changing the Oil. Dispose of the old oil in accordance to Federal, State and Local regulations.

5.Thoroughly clean the unit and inspect for any loose or damaged parts. Repair or replace damaged parts and tighten loose screws, nuts or bolts. The unit is ready for storage.

TRANSPORTING

•Allow the engine to cool before transporting.

•Secure the unit while transporting.

•Drain the gas tank before transporting.

•Tighten gas cap before transporting.

5. Install a correctly-gapped sparkFig. 35 plug in the cylinder head. Turn

the 5/8 in. socket clockwise until snug.

13