WARNING: OVERFILLING OIL CRANKCASE MAY CAUSE SERIOUS PERSONAL INJURY. Check and maintain the proper oil level in the crank case; it is important and cannot be overemphasized. Check the oil before each use while the engine is cold and change

t as needed. See Changing the Oil.

RECOMMENDED OIL TYPE

Using the proper type and weight of oil in the crankcase is extremely important. Check oil before each use while the engine is cold and change the oil every 25 hours of operation. Failure to use the correct oil, or using dirty oil, can cause premature engine wear and failure.

Use a high-quality SAE 30 weight oil of API (American Petroleum Institute) service class SF, SG, SH.

ADDING OIL TO CRANKCASE: INITIAL USE

NOTE: This unit is shipped without oil. In order to avoid damage to the unit, put oil in the crankcase before you attempt to start the unit.

Your unit is supplied with one 3.04 fluid oz. (90 ml.) bottle of SAE 30 SF, SG, SH oil (Fig. 10).

NOTE: Save the bottle of oil. It can be used to measure the

correct amount during

future oil changes (Fig. O-Ring Oil Fill Plug

10). See Changing the Oil.

1.Unscrew the top of the bottle of oil and remove the paper seal covering the opening. Replace the top. Next, cut the tip off the funnel spout (Fig. 10).

2.Remove the oil fill plug from the crankcase (Fig. 11).

3.Tilt the unit 30 ° to the side

(Fig.

12).

Fig. 11

4. Pour

the entire bottle of oil

 

into the oil fill hole (Fig. 12). NOTE: Never add oil to the fuel or

fuel tank.

5.Wipe up any oil that may have

spilled and reinstall the oil fill plug.

Check oil before each use while the

engine is cold and change the oil every 25 hours of operation. Refer to

Checking the Oil Level.

CHECKING THE OIL LEVEL

I

I

RECOMMENDED FUEL TYPE

Old fuel is the primary reason for improper unit performance. Be sure to use fresh, clean, unleaded gasoline.

NOTE: This is a four-cycle engine. In order to avoid damage to the

unit, do not mix oil with gasoline. Definition of Blended Fuels

Today's fuels are often a blend of gasoline and oxygenates such as ethanol, methanol or MTBE (ether). Alcohol-blended fuel absorbs water. As little as 1% water in the fuel can make fuel and oil

separate or form acids when stored. Use fresh fuel (less than 60 days old), when using alcohol-blended fuel.

Using Blended Fuels

If you choose to use a blended fuel, or its use is unavoidable, follow recommended precautions:

Always use fresh unleaded gasoline

Use the fuel additive STA-BIL® or an equivalent

Drain tank and run the engine dry before storing unit Using Fuel Additives

outdoor area. Wipe up any spilled fuel immediately.

_lk WARNING: Add fuel in a clean, well ventilated Avoid creating a source of ignition for spilt fuel. Do not

start the engine until fuel vapors dissipate.

vaporsWARNING:may explode. Always stop the engine and allow Gasoline is extremely flammable. Ignited it to cool before filling the fuel tank. Do not smoke while

filling the tank. Keep sparks and open flames at a distance from the area.

The use of fuel additives, such as STA-BIL® Gas Stabilizer or an equivalent, will inhibit corrosion and minimize the formation of gum deposits. Using a fuel additive can keep fuel from forming harmful deposits in the carburetor for up to six (6) months. Add 0.8 oz. (23 ml.) of fuel additive per gallon of fuel according to the instructions on the container. NEVER add fuel additives directly to the unit'sgas tank.

FUELING THE UNIT

fromWARNING:fuel spray. Never operate the unit without the fuel I Remove fuel cap slowly to avoid injury [

cap secure y n p ace.

1.Remove the fuel cap.

2.Place the gas container's spout into the fill hole on the fuel tank (Fig. 14) and fill the tank.

Check the oil only when the engine is

Fig. 12

off and cool.

 

1.Place the unit on its stand on a level surface.

2.Remove the oil fill plug from the crankcase (Fig. 11).

3.Look into the oil fill hole (Fig. 11). If the oil level comes up to the first thread, then the oil is full (Fig. 13). If it does not, fill with oil until it does.

Gas C!t

Spout

Fuel Tank

Fig. 14

Oil Full Line

Fig. 13

NOTE: Do not overfill the tank.

3.Wipe up any gasoline that may have spilled.

4.Reinstall the fuel cap.

5.Move the unit at least 30 ft. (9.1 m) from the fueling source and site before starting the engine.

NOTE: Dispose of the old gasoline in accordance to Federal, State

and Local regulations.

8

Page 8
Image 8
Craftsman 79480 manual Recommended OIL Type, Adding OIL to Crankcase Initial USE, Recommended Fuel Type, Fueling the Unit

79480 specifications

The Craftsman 79480 is a versatile and powerful tool designed to meet the needs of both DIY enthusiasts and professionals alike. Known for its robust performance, this tool combines innovative technologies with user-friendly features to enhance efficiency and convenience.

One of the key features of the Craftsman 79480 is its high-torque motor, which delivers exceptional power for various tasks. This makes it ideal for heavy-duty applications such as drilling, driving screws, and handling tough materials. The motor is designed to operate smoothly with reduced noise levels, allowing users to work in quieter environments without sacrificing performance.

Another significant aspect of the Craftsman 79480 is its variable speed control. This feature allows users to adjust the speed according to the specific requirements of their projects, providing greater control and precision. Whether you are working on delicate tasks or need to drive screws rapidly, the variable speed settings cater to a wide range of applications.

The tool is equipped with an ergonomic handle that enhances comfort during use. The soft-grip design provides better control and reduces fatigue, allowing users to work efficiently over extended periods. Additionally, the lightweight construction of the Craftsman 79480 makes it easy to maneuver and handle, enhancing overall usability.

Craftsman also emphasizes safety in the design of the 79480. It includes an integrated safety clutch that prevents damage to the tool and work materials by disengaging the motor when excessive force is applied. This not only prolongs the life of the tool but also ensures that users can work with confidence.

Furthermore, the Craftsman 79480 features a durable build, constructed from high-quality materials that withstand the rigors of daily use. Its robustness contributes to the longevity of the tool and makes it a reliable companion for any project.

In conclusion, the Craftsman 79480 stands out in the market with its powerful motor, variable speed control, ergonomic design, safety features, and durable construction. Whether you are a professional or a hobbyist, this tool offers the versatility and reliability needed to tackle a broad spectrum of tasks, making it a valuable addition to any toolkit.