Craftsman 257.796362 manual Arnings And Safety Instructions, A. Operator Safety, B. Tool Safety

Models: 257.796362 79636

1 12
Download 12 pages 50.19 Kb
Page 3
Image 3
ARNINGS AND SAFETY INSTRUCTIONS

ARNINGS AND SAFETY INSTRUCTIONS

Failure to follow all Safety Rules and Precautions can result in serious injury.

WARNING: Thew ing andsafetyinstructions in this manual must be followed to reduce the

risk of fire, electric shock, or injury, and to provide reasonable safety and efficiency in using this tool. The

operator is responsible for following the warnings and instructions in this manual and on the unit. Read the

entire Operator's Manual before assembling and using the unit[ Restrict the use of this tool to persons who

read, understand, and follow the warnings and instructions in this manual and on the unit.

A. OPERATOR SAFETY

1.Always wear eyeprotection to prevent rocks or de- bris from being blown or ricocheting into eyes and face which can result in blindness or serious injury.

2.Always wear a respirator or facemask when working with the unit in dusty environments.

3.Always wear heav_ long pants, boots, and

gloves. Do not go barefoot or wear short pants, san-

dais, jewelry, loose clothing, or clothing with loosely hangl'ng straps, ties, tassels, etc.. Secure hair so it is

above shoulder length. Being fully covered will help

protect you from pieces ofto_c plants such as poison ivy thrown by the blade, which could be more of a

hazard than touching the plant itself. Use of r_bber gloves is recommended.

4.Keep hair, fingers, and all other parts of the

body away from openings and moving parts.

5.Do not operate the unit when you are tired, ill, upset, or if you are under the influence of alcohol, drugs, or medication.

6.Keep children, bystanders, and animals away

from the work area a minimum of 30 feet when oper- ating the unit.

7.nspect the area before using the unit. Remove all debris and hard objects such as rocks, glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation. As a vacuum, the

unit is designed to pick up d_ material such as leaves, grass, small twigs, and bits of paper. Do not vacuum stones, gravel, metal, broken glass, etc. to

avoid severe damage to the impeller. Do not attempt to vacuum water or other liquids to avoid the possi- bility of electrlcal shock.

B. TOOL SAFETY

1. Stop the motor and disconnect the power source before opening the vacuum inlet door or at- tempting to insert or remove the vacuum tubes. The motor must be stopped and the impeller blades no longer turning to avoid serious injury from the rotat- ingblades.

2.Inspect the entire unit before each use for worn, loose, missing, or damaged parts. Do not use until the unit is in proper working order.

3.Have all internal service performed by Sears qu- alified service repair personnel to avoid creating a hazard or voiding your warranty.

4.Have all maintenance other than the recom-

mended procedures described in the Operator's

Manual performed by Sears qualified service repair personnel.

5.Always see your Sears Service Center_epart-

merit to replace a damaged impeller. Parts that are chipped, cracked, broken, or damaged in any oth- er way can fly apart and cause serious injury. Replace damaged parts before using the unit.

6.Never run the unit without the proper equip-

ment attached.

When used as a blower, always in-

stall a blower tube. When used as a vacuum, always install vacuum tubes and collection bag assembly. Make sure collection bag assembly is completely zipped.

7.Do not use any accessory or attachment other than

those recommended by Sears for use with your unit.

C.ELECTRICAL SAFETY

L Use only a 120 A.C. voltage supply as shown on the name plate of the tool.

2. Avoid dangerous situations. Do not use in the

presence of flammable liquids (such as gasoline) or gases to avoid creating a fire or explosion and/or causing damage to the unit.

3.Do not use in dampor wet locations or around

swimming pools, hot tubs, etc. Do not handle

plug or unit _th wet hands. Do not expose to snow,

rain, or water to avoid the possibility of electrical shock.

4.Use extension cords specifically" marked as

suitable for outdoor use. Match v_re gau_e to the cord length. See the "Extension Cord" sechon.

5.Inspect the insulation and connectors on the

unit and extension cord before each use. Do not use with damaged cord or plug. If unit is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, do not use until

damage is repaired by Sears qualified service person- nel.

6.Never carry the unit by the extension cord or yank the extension cord to disconnect the unit.

7.Use the cord retainer as described in this mamml to prevent extension cord disconnection.

8.Do not use the unit if the switch does not turn

the tool on and off properly Repairs to the

switch must be made by Sears qualified servlce per- sonnel.

9.Keep extension cord clear of operator and ob- stacles at all times. Do not close a door on cord. Do

not expose cords to heat, oil, water, or sharp edges.

10.Avoid any body contact with any grounded

conductor, such as metal pipes or w1_refences, to avoid the possibility of electrical shock.

D.OPERATION SAFETY

1.Keep others including children, animals, by-

standers, and helpers a minimum of 30 feet

away. Stop the motor immediately if you are ap- proached.

2.Inspect the area before using the unit. Remove all debris and hard objects such as rocks, glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation. As a vacuum, the unit is designed to pick up dry material such as leaves, grass, small twigs, and bits of paper. Do not vacuum stones, gravel, metal, broken glass, etc. to

avoid severe damage to the impeller. Do not attempt to vacuum water or other llqu_ds to avoid the possi- billty of elecwical shock.

3.Avoid accidental starting. Be sure the switch is in the "off" position and keep your hand and fingers away from the switch while connecting the unit to an extension cord or when carrying a unit connected to a power source.

4.Stop unit and disconnect from power source when not in use.

-3-

Page 3
Image 3
Craftsman 257.796362 manual Arnings And Safety Instructions, A. Operator Safety, B. Tool Safety, C.Electrical Safety