TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

1.Make sure transaxle is in neutral (N). NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

2.Loosen adjustment bolt in front of the right rear wheel.

3.Position the gear shift lever in the neutral (N) position.

4.Tighten adjustment bolt securely. NOTE: If additional clearance is needed

to get to adjustment bolt, move mower deck height to the lowest position.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant

may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

Washers

Retainin(

Ring

Axle

Cover

i

Square Key

(Rear Wheel Only)

TO START ENGINE WITH A WEAK

Gearshift Lever

Neutral Lock Gate

 

Adjustment Bolt

BATTERY

,_CAUTION: Lead-acidbatteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries.

Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BA'I-I'ERY"in the MAINTENANCE section of this manual).

If "jumper cables" are used for emergency starting, follow this procedure:

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steering wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are

not adjustable on your tractor. If damage has occurred to affect the front wheel

toe-in or camber, contact a Sears or other qualified service center.

TO REMOVE WHEEL FOR REPAIRS

IMPORTANT: Your tractor is equipped with a 12 volt negative grounded system. The other vehical must also be a 12 volt negative grounded system. Do not use your tractor

battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect each end of the RED cable to the POSITIVE (+) terminal of each battery, taking care not to short against chassis.

2.Connect one end of the BLACK cable

to the NEGATIVE (-) terminal of fully charged battery.

3.Connect the other end of the BLACK cable to good CHASSIS GROUND, away from fuel tank and battery.

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

TO REMOVE CABLES, REVERSE ORDER -

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

24

Page 24
Image 24
Craftsman 917.27207 owner manual Transaxle Gear Shift Lever Neutral Adjustment, To Start Engine with a Weak, Battery

917.27207 specifications

The Craftsman 917.27207 is a versatile and robust lawn mower that combines power, efficiency, and user-friendly features, making it an excellent choice for homeowners looking to maintain their lawns effortlessly. This walk-behind mower is designed to tackle various grass types and terrains, ensuring a clean, even cut every time.

One of the standout features of the Craftsman 917.27207 is its powerful engine. Equipped with a dependable 159cc engine, it provides ample power to handle even the thickest grass. The manual start ensures reliability, allowing users to get their mowing tasks done quickly without worrying about battery issues. The engine is designed for fuel efficiency, helping homeowners save on gas while minimizing their environmental footprint.

In addition to its powerful engine, the Craftsman 917.27207 features a 21-inch cutting deck. This mid-sized deck strikes a perfect balance between maneuverability and cutting capacity, making it ideal for small to medium-sized lawns. The steel construction adds durability, promising longevity and resilience against wear and tear.

Another key characteristic of the Craftsman 917.27207 is its adjustable cutting heights. With six different height settings, ranging from 1.25 inches to 3.75 inches, users can customize their mowing experience to achieve their desired grass length. This feature is particularly beneficial during different seasons when grass growth varies.

The mower also includes a rear bagger option, making grass collection efficient and hassle-free. The 2-in-1 functionality allows users to choose between mulching and bagging, providing flexibility based on their lawn care preferences. The mulching feature finely chops grass clippings, allowing them to return to the lawn as natural fertilizer, promoting healthier growth.

In terms of ergonomics, the Craftsman 917.27207 is designed with user comfort in mind. The adjustable handle provides customizable height options, ensuring that users can mow comfortably without straining their backs. Lightweight yet sturdy, the mower is easy to maneuver around obstacles and tight corners.

Ultimately, the Craftsman 917.27207 brings together power, performance, and adaptability, making it a solid choice for any DIY lawn care enthusiast. With its impressive features and reliable engineering, keeping lawns looking their best has never been easier.