ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL

CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

1.With engine not running, move throttle control lever from slow to choke posi- tion. Slowly move lever from choke to fast position.

2.Check that holes "A" in governor

control lever and hole in governor plate line-up. If holes "A" are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

Governor Control Lever Governor Control Plate

/

"A"

Clamp Screw

Cable

TO ADJUST

CARBURETOR

 

NOTE: The carburetor on this engine is low emission. It is equipped with an idle fuel adjusting needle with a limiter cap,

which allows some adjustment within the limits allowed by the cap. Do not attempt to remove the limiter cap. The limiter cap cannot be removed without breaking the adjusting needle.

The carburetor has been preset at the factory and adjustment should not be

necessary. However, minor adjustment may be required to compensate for differ- ences in fuel, temperature, altitude or load. If the carburetor does need adjustment, proceed as follows:

In general, turning idle mixture valve in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mix- ture. Turning the idle mixture valve out

(counterclockwise) increases the supply

of fuel to the engine giving a richer fuel/air mixture.

IMPORTANT: Damage to the needle

valve and the seat in carburetor may result if screw is turned in too tight.

PRELIMINARY SETTING -

1.Air cleaner assembly must be assem- bled to the carburetor when making carburetor adjustments.

2.Be sure the throttle control cable is adjusted properly (see above).

FINAL SETTING -(See "TO ADJUST THROTTLE CONTROL CABLE" in this

section of the manual.)

1.Start engine and allow to warm for five minutes. Make final adjustments with engine running and shift/motion control lever in neutral (N) position.

2.Move throttle control lever to slow posi- tion. With finger, rotate and hold throttle lever against idle speed screw. Turn idle speed screw to attain 1750 RPM.

3.While still holding throttle lever against

idle speed screw, turn idle mixture valve full travel clockwise then counter-

clockwise until engine runs rough. Turn valve to a point midway between those two positions. Release throttle lever.

ACCELERATION TEST -

4.Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle mixture valve out (coun-

terclockwise) 1/8 turn. Repeat test and continue to adjust, if necessary, until

engine accelerates smoothly.

High speed stop is factory adjusted. Do not adjust or damage may result.

IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous. If you think the

engine-governed high speed needs adjust- ing, contact a Sears or other qualified ser- vice center, which has proper equipment and experience to make any necessary adjustments.

Idle Speed

Lever

Idle Mixture

Valve with

Limiter

27

Page 26 Page 28
Page 27
Image 27
Craftsman 917.2754 Engine, To Adjust Throttle Control Cable, To Adjust Carburetor, Preliminary Setting, Acceleration Test
Page 26 Page 28

917.2754 specifications

The Craftsman 917.2754 is a state-of-the-art lawn tractor that stands out in the market for its robust features, advanced technologies, and practical design aimed at enhancing user experience and mowing efficiency. It is particularly favored by homeowners with extensive lawns, thanks to its powerful engine and user-friendly functionality.

One of the key features of the Craftsman 917.2754 is its powerful 24 HP engine, which provides ample horsepower to tackle various terrains and challenging mowing conditions. The engine is not only efficient but also reliable, ensuring that users can depend on it season after season. Coupled with a hydrostatic transmission, the driving experience is smooth, allowing for effortless control over speed and direction without the hassle of shifting gears.

The 42-inch cutting deck of the Craftsman 917.2754 is designed for optimal performance and efficiency. This size makes it perfect for maneuvering in tighter spaces while still covering a significant area of lawn in a single pass. The deck features an adjustable cutting height, allowing users to customize their mowing experience based on grass type and weather conditions, ensuring a clean and precise cut every time.

Another highlight of the Craftsman 917.2754 is its comfortable seating and ergonomic design. The high-back seat provides exceptional support, allowing users to maintain comfort during long mowing sessions. The intuitive control panel is user-friendly, equipped with easy-to-read dials and controls for direct access to critical functions such as throttle and cutting height adjustments.

For added convenience, the Craftsman 917.2754 also includes a tight turning radius, making it easier to navigate around obstacles like flower beds and trees. This feature reduces the need for additional trimming, saving users both time and effort. Furthermore, the integrated mulching capability allows for efficient grass recycling, promoting healthier lawn growth.

Durability is a hallmark of the Craftsman brand, and the 917.2754 exemplifies this with its sturdy construction and long-lasting components. Owners can enjoy peace of mind knowing that their investment is built to withstand the rigors of regular lawn maintenance.

In summary, the Craftsman 917.2754 lawn tractor combines power, efficiency, and comfort into a single machine, making it an excellent choice for homeowners looking to maintain their lawn effortlessly. Its advanced features and practical design set it apart in the lawn care landscape, providing users with a dependable and enjoyable mowing experience.
Top Page Image Contents