Craftsman 917.376531 owner manual Lawn Mower, Drive Wheels

Models: 917.376531 37653

1 52
Download 52 pages 30.84 Kb
Page 14
Image 14

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TIRES

Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

DRIVE WHEELS

Check front drive wheels each time before you mow to be sure they move freely.

The wheels not turning freely means trash,

grass cuttings, etc. are in the drive wheel area and must be cleaned to free drive wheels.

If necessary to clean the drive wheels, be sure to clean both front wheels.

1.Remove hubcaps, Iocknuts & washers.

2.Remove wheels from wheel adjusters.

3.Remove any trash or grass cuttings from inside the dust cover, pinion and/ or drive wheel gear teeth.

4.Put wheels back in place.

NOTE: If after cleaning, the drive wheels do not turn freely, contact a Sears or other qualified service center.

BLADE CARE

For best results, mower blade must be kept sharp. Replace a bent or damaged blade. A CAUTION: Use only a replacement blade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is haz- ardous, could damage your mower and void your warranty.

TO REMOVE BLADE

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air filter and carburetor are up.

3.Use a wood block between blade and

mower housing to prevent blade from turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter- clockwise.

5.Remove blade and attaching hardware

(bolt, lock washer, hardened washer). NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged.

TO REPLACE BLADE

1.Position the blade adapter on the en- gine crankshaft. Be sure key in adapter and crankshaft keyway are aligned.

2.Position blade on the blade adapter.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on blade adapter.

3.Be sure trailing edge of blade (opposite sharp edge) is up toward the engine.

4.Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.

5.Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

The recommended tightening torque is 35-40 ft. Ibs.

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approved bolt shown in the Repair Parts section of this manual.

Blade adapter

Key

Crankshaft

Lockwasher

Blade

Blade

 

 

 

bolt

Hardened

_

'_

 

washer

Trailing/edge

retainer

TO SHARPEN BLADE

NOTE: We do not recommend sharp-

ening blade - but if you do, be sure the blade is balanced. An unbalanced blade

will cause eventual damage to lawn mower or engine.

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with it.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

Center hole

5/8" bolt or pin

14Blade

Page 14
Image 14
Craftsman 917.376531 owner manual Lawn Mower, Drive Wheels

917.376531, 37653 specifications

The Craftsman 37653,917.376531 is a powerful and versatile power tool designed to meet the needs of both professional contractors and DIY enthusiasts. This tool stands out for its robust build quality and reliability, making it a cornerstone for any workshop or job site.

At the core of the Craftsman 37653 is a high-performance motor that provides impressive torque output, enabling users to tackle a wide variety of tasks with ease. Whether you're drilling, driving screws, or working with tough materials, this tool is engineered to deliver consistent performance. The variable speed settings allow users to adjust the speed according to the materials and tasks at hand, offering precision and control for intricate projects.

One of the standout features of the Craftsman 37653 is its ergonomic design. It boasts a comfortable grip that reduces fatigue during prolonged use, allowing users to work longer without discomfort. The tool's lightweight nature enhances portability, making it easy to transport from job to job or to work in confined spaces.

In terms of technologies, the Craftsman 37653 incorporates advanced battery management systems that ensure optimal battery life and performance. This allows users to work without worrying about frequent recharging, boosting productivity on the job. The quick-charge capability further enhances usability, giving users the ability to get back to work swiftly.

Durability is another key characteristic of the Craftsman 37653. Constructed from high-quality materials, it is designed to withstand tough working conditions, providing peace of mind to users who might operate in demanding environments. Additionally, the tool often comes with a protective case, which not only aids in storage but also provides extra protection during transport.

Safety is of paramount importance in power tools, and the Craftsman 37653 delivers with features such as a built-in safety lock. This prevents accidental activation, crucial for maintaining user safety during operation. Moreover, the design frequently includes LED lights that illuminate the work area, allowing for better visibility in low-light conditions.

In conclusion, the Craftsman 37653,917.376531 combines power, versatility, and safety, making it an indispensable tool for anyone serious about craftsmanship. Whether for home improvement or professional construction, its features, technologies, and characteristics cater to a broad spectrum of applications, ensuring it stands as a reliable partner in any project.