Craftsman 973.2748.70 owner manual Do not Charge Battery Tool in a Damp or WET Location

RULES FOR SAFB_OPERATION (Continued)

iNEVER USE IN AN EXPLOSIVE ATMO- SPHERE. Normal sparking of the motor could ignite flammable liquids, gases, or fumes.

mKEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products or any strong solvents to clean your tool.

nSTAY ALERT. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush.

MCHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate propedy and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mountings,and any-otherconditions that may affect its operation. A guard or other part that is damaged should be propedy repaired or replaced by an authodzed service center unless indicated elsewhere in this instruction manual.

DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

DRUGS, ALCOHOL, MEDICATION. Do not operate tool while under the influence of drugs, alcohol, or any medication.

DRILLING OR DRIVING SCREWS INTO ELECTRICAL WIRING IN WALLS, CEILINGS, OR OTHER AREAS CAN CAUSE THE BIT OR CHUCK TO BECOME ELECTRICALLY LIVE. Do not touch metal parts when drilling into a wall; grasp only the insulated handle(s) or plastic housing when using this tool. Make sure hidden electrical wiring, water pipes, and mechanical hazards are n_otin _he path of the bit when ddlling into a wall.

•INSPECT FOR and remove all nails from lumber before ddlling.

DO NOT PLACE BA'n'ERYTOOLS OR THEIR BAI-rERIES NEAR FIRE OR HEAT. They may explode.

DO NOT CHARGE BATTERY TOOL IN A DAMP OR WET LOCATION.

Your battery tool should be charged in a location where the temperature is more than 50°F but less than 100°F.

Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water, then neutralize with lemon juice or vinegar. If liquid gets in your eyes, flush them with clean water for at least 10 minutes, then seek immediate medical attention.

If carrying your battery tool at your side, make sure it is not running and your finger is not on the switch. Avoid accidental starting.

SECURE WORK before applying power. NEVER hold workpiece in your hand or across your legs.

WHEN SERVICING USE ONLY IDENTICAL CRAFTSMAN REPLACEMENT PARTS.

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER

•SAVE THESE INSTRUCTIONS. This manual

contains important safety and operating instructions for battery charger part number 977412-001.

•Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, and product using battery charger.

AWARNING: To reduce dsk of injury, charge only 41_ nickel-cadmium type rechargeable batteries.

Other types of battedes may burst causing pemonal injury and damage.

•Do not expose charger to rain or snow.

IMPORTANT SAFETY RULES FOR BATTERY TOOLS

Battery tools do not have to be plugged into an electricaloutiet; therefore, they are always in operating condition. Be aware of possible hazards when not using your battery tool or when changing accessodes.

USE ONLY THE CHARGER PROVIDED WITH YOUR BA'I-rERY TOOL. Do not substitute any other charger. Use of another charger could cause batteries to explode causing possible sedous injury.

•

Use of an attachment not recommended or sold

by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons.

To reduce dsk of damage to charger body and cord, pull by charger body rather than cord when disconnecting charger.

Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.

4