INSTALLATION INSTRUCTIONS

Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure) and the adjustment conditions are compatible. The adjustment conditions for this appliance are stated on the data badge which is fitted behind the bottom of the main oven door seal.

This appliance is not designed to be connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. particular attention should be given to the relevant requirements regarding ventilation.

MODEL NUMBER: S230G

Category I2H (GB. IE)

These models are set to burn NATURAL GAS (G20) at 20 mbar ONLY and can not be used on any other gas.

GAS SAFETY (INSTALLATION & USE) REGULATIONS

It is the law that all gas appliances are installed by competent persons in accordance with the cur- rent edition of the above regulations. It is in your interest and that of safety to ensure compliance with the law.

In the UK, CORGI registered installers work to safe standards of practice. The appliance must also be installed in accordance with BS 6172. Failure to install the appliance correctly could invalidate the warranty liability claims and could lead to prosecution.

LOCATION

The appliance may be located in a kitchen, kitchen/diner or a bed-sitting room, but not in a room containing a bath or shower. The appliance must not be installed in a bed-sitting room of less than 20m3.

PROVISION FOR VENTILATION

The room containing the appliance should have an air supply in accordance with BS 5440: Part 2.

The room must have an opening window or equivalent; some rooms may also require a permanent vent. If the room has a volume between 5 and 10m3, it will require an air vent of 50cm2 effective area unless it has a door which opens directly to outside. If the room has a volume of less than 5m3, it will require permanent air vent of 100cm2 effective area. If there are other fuel burning appliances in the same room, BS 5440: Part 2 should be consulted to determine air vent requirements.

TECHNICAL DATA

Gas connection

Rp 1/2 (1/2" BSP female)

Gas supply

G20 at 20 mbar.

Pressure test point

Grill injector

Electrical connection

Flexible cord fitted with a 3 pin 13 amp plug.

 

230 - 240 a.c. 50HZ 3A fuse

BURNER

HEAT INPUT

INJECTOR

Grill

3.4 kW

150

Main Oven

2.4 kW

110

Top Oven

1.65 kW

095

26

Page 26
Image 26
Creda S230G installation instructions Installation Instructions

S230G specifications

The Creda S230G is a versatile and powerful electric storage heater that combines advanced technology with user-friendly features to provide efficient heating solutions for homes and commercial spaces. Designed with a modern aesthetic, the S230G seamlessly integrates into various interior designs while providing optimal warmth and comfort.

One of the standout features of the Creda S230G is its advanced energy storage capability. This heater operates by charging during off-peak energy hours, allowing users to take advantage of lower electricity rates. The unit stores heat in its ceramic bricks, which then gradually release warmth throughout the day, ensuring a consistent and comfortable indoor temperature. This not only promotes energy efficiency but also helps in reducing overall heating costs.

The Creda S230G is equipped with a built-in thermostat that allows for precise temperature control. Users can easily set their desired temperature, and the heater will automatically adjust its output to maintain that level of comfort. Additionally, the S230G features a manual control panel, making it easy to operate and customize heat settings to suit individual preferences.

Another notable technology integrated into the Creda S230G is its adaptive control system. This innovative feature learns the user's heating patterns and preferences over time, optimizing its performance to meet specific needs. This personal touch enhances comfort while ensuring energy is used efficiently, contributing to lower utility bills.

The heater's construction is robust, featuring high-quality materials that ensure durability and longevity. Safety is also a priority, with built-in overheat protection and a thermal cut-out feature designed to prevent potential hazards.

Installation of the Creda S230G is straightforward, making it a practical choice for both new builds and retrofitting projects. The unit can be mounted on walls to save space, and its compact size allows it to fit into various room layouts without being intrusive.

In summary, the Creda S230G stands out as an exceptional electric storage heater. Its energy-efficient design, user-friendly features, adaptive control system, and high-quality construction make it a reliable choice for heating needs. With the capability to provide consistent warmth while optimizing energy usage, the S230G is an ideal solution for those looking to enhance their living or working environment with effective heating technology.