The volume control can be operated manually at any time, whether the OBH-22 is powered or not, but without power only Line 1 can be utilised.

MAINS CONNECTION

When unpacking the module please keep the packing material in a safe place for possible future use. In the pack there is a separate mains adaptor, prepared for the mains voltage supply in the country of use. The plug at the end of the fixed cable should be firmly inserted into the connector on the OBH-22 rear panel marked “DC inlet". Remember, do not overload the mains wall socket with too many

plugs or adaptors. If in doubt, please contact your supplying dealer or a qualified electrician. The OBH-22 draws less than 2 Watts of power from the mains under all conditions so it can safely be left switched on without significantly increasing your electricity bill.

INPUT AND OUTPUT CONNECTIONS

Line 1 and 2 are identical. The output from a CD, Tuner, AV or from an OBH-15 or OBH-18 phono pre-amp can be connected to either of them. For tape machines, use the Tape input and output - the tape monitor function will allow recordings to be made and played back. The output from the OBH-22 should be connected to a power amplifier with suitable sensitivity (gain). Remember, the OBH-22 will not increase the signal from input to output.

VOLUME LEVEL

The volume control is used to alter the relative level of the sound output from the amplifier. It is important to realise that the volume control only acts to reduce, or attenuate, the incoming signal to the power amplifier stage. The maximum power of an amplifier is available only if the level of signal available from line level equipment is sufficient to drive it to clipping, which will be different from one amplifier to another. The volume control is therefore also used to balance the level from one piece of equipment to another.

If it is found necessary to have the volume control set to a position which is considered to be high before the desired level of volume is obtained, it does not necessarily mean that the amplifier is having to work too hard or "flat-out". Consult your dealer if you need more advice. Always have the volume control set at minimum (counter-clockwise) when switching your amplifier on and off, to avoid thumps or sudden loud noises.

POSITIONING OF THE OBH-22

The OBH-22 needs to be powered from its adaptor to operate the volume, input and mute functions via the remote control. It will work best if placed on a suitable hard surface or Hi-Fi equipment cabinet. Should it be necessary to place the OBH-22 on the top of other audio or video equipment, avoid obstructing any ventilation slots that could cause overheating, or internal mains transformers which might induce hum pick-up. Very heavy signal interconnects may cause the OBH-22 to tip backwards. There are two slots on the bottom that could be used to lock it in position. Do not obstruct the IR sensor on the front panel.

OPERATING THE OBH-22 BY REMOTE CONTROL

The OBH-22 has three line inputs including tape, which can be selected either from the front panel buttons or remote handset. The appropriate LED above each button will indicate which one is selected. Volume level can be adjusted manually from the control knob on the front panel or by using the up and down buttons on the remote handset. Remote volume changes will cause the input indicator LED to flash.

Pressing the Mute button on the front panel or remote handset will short the signal to ground and the LED indicator will light above the button. To un-mute, press the Mute button again or the volume up button (volume down will not un-mute the signal). To un-mute the OBH-22 without the handset, remove the power supply for 10 secs. To select the tape player or to monitor a tape recording press button ‘Tape 1’. The LED indicator will light. Press button ‘Tape 1’ again to switch this off. All other buttons on the handset are reserved for other Creek remote controlled products.

CAUTION

Your OBH-22 amplifier is designed to give you years of reliable use. However, it is necessary to take care of your possession, so never overheat and only use the recommended Creek OBH 1 power supply.

The OBH-22 is designed to comply with European EMC requirements. However, it should be noted that it is not possible to guarantee faultless operation of the equipment if it is used close to the source of high powered radio transmissions, such as can be found in mobile telephones or CB radio etc. Care should also be taken to place it away from the source of mains interference caused by mains transformers in other equipment. Electrical switching noises from domestic or industrial heating systems, conducted periodically down the mains supply, can sometimes be amplified and present themselves as a click or a thump through a Hi-Fi system.

If you suspect that a fault has developed, do not remove the cover plate. There are no user serviceable parts inside. If you are unfortunate enough to need service work carried out on the OBH-22, it should be returned to your dealer for his expert help, in the original packing material if possible.

Page 1 Page 2
Page 2
Image 2
Creek Audio OBH22 manual Mains Connection, Input and Output Connections, Volume Level, Positioning of the OBH-22
Page 1 Page 2

OBH22 specifications

The Creek Audio OBH22 is a highly regarded headphone amplifier known for its exceptional sound quality and compact design. Designed for audiophiles and casual listeners alike, this amplifier provides a seamless listening experience whether you're using it with your home audio system or portable devices.

One of the main features of the OBH22 is its ability to drive a wide range of headphones, from high-impedance studio models to low-impedance designs. This versatility makes it an attractive choice for users with various headphones. The amplifier's output power is sufficient to ensure that even power-hungry models perform at their best, delivering a clear and dynamic sound profile that captures the listener's attention.

The OBH22 incorporates high-quality materials and craftsmanship in its build, which is evident in its sleek, compact chassis. The design is not only aesthetically pleasing but also functional. It features a minimalist layout with a large volume control knob, input selector switch, and headphone output on the front panel. This simplicity allows users to easily navigate between multiple inputs without confusion.

In terms of technology, the OBH22 uses an advanced circuit design that prioritizes signal integrity and low distortion. The amplifier features a dedicated power supply that ensures a clean and stable power source, thereby enhancing audio performance. Creek Audio employs proprietary design techniques that minimize noise and interference, further contributing to the overall sound quality.

The amplifier offers both RCA input and output connections, making it compatible with a variety of audio sources, including CD players, digital audio players, and even computers. This broad compatibility ensures that users can integrate the OBH22 into their existing audio setups without hassle.

Another noteworthy characteristic of the Creek Audio OBH22 is its impressive tonal balance. It delivers a rich and warm sound signature with excellent clarity across all frequency ranges. This balanced response allows listeners to fully appreciate the nuances of their favorite music genres, whether it be classical, jazz, rock, or electronic.

The Creek Audio OBH22 is not just an amplifier; it is a gateway to a better listening experience. With its combination of high-quality audio performance, robust design, and user-friendly features, it's a compelling choice for anyone looking to elevate their headphone listening experience.
Top Page Image Contents