`` SPECIFICATIONS

Performance

Frequency Reponse (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz ± 1 dB.

Frequency Response (at line out): 20 Hz to 20 kHz ± 1 dB.

Power Bandwidth (at 4-ohm tap, 2 dB below maxium 1 kHz power): 50 Hz to 20 kHz with < 0.5% THD

Signal to Noise Ratio (ref. to rated power, master volume at minimum): 85 dB.

DC Output Offset: < ±5 mV.

THD: Less than 0.5% at rated power at 1 kHz.

Input Sensitivity (for full output at maximum gain):

Balanced mic inputs: 3 mV.

Balanced line inputs: 800 mV.

RCA connectors: 400 mV.

Input Impedance (nominal):

Mic: 400 ohms.

Line: 100 kilohms.

RCA: 50 kilohms.

Crosstalk: –70dB at 1kHz.

Line Output Level (nominal): 1V into 10 kilohms.

Phantom Power: 15 VDC.

AC Line Voltages Available:

100V 50/60 Hz

120V 60 Hz

220V 50/60 Hz

230V 50/60 Hz

240V 50/60 Hz

Operating Temperature/Humidy: 0° C to 40° C at 95% relative humidity (non-condensing).

Storage Temperature: –20° C to 85° C.

Front Panel Controls and Indicators

Power Switch: Pushbutton on-off switch. The power switch does not affect the 24V DC auxiliary power input.

Input Volume Controls: Microphone/line, four in 180MA and 1160MA, eight in 280MA. Detented potentiometers with knobs.

Tone Controls: Bass and Treble non-detented recessed potentiometers on each input chan- nel. Bass ±10 dB at 100 Hz, Treble ±10 dB at 10 kHz.

Power Indicator: Blue LED indicates power on.

Input Signal Presence Indicator: Green LED, one for each input channel, illuminates when input signal exceeds –24 dBu (line) or –70 dBu (mic).

Output Signal Presence Indicator: Green LED, one for each output channel, illuminates when output signal level exceeds 100 mV (45 dB below full power) from the 4-ohm tap. Does not respond to signals from the AMP INPUT connector.

Clip Indicators: Red LED, one per output chan- nel. Illuminates at threshold of audible distor- tion. Does not respond to signals from the AMP INPUT connector.

Output Volume Controls: One per output chan- nel. Detented potentiometer with knob.

Back Panel Controls and Connectors

Reset Switch: Resets the circuit breaker that protects the power supply. 220/230/240V units have a fuse instead.

AC Power Inlet: Detachable IEC.

Auxiliary Power Input: 2-position terminal strip for 24 VDC (±10%) backup power. Accepts up to 14 AWG terminal forks.

Amplifier Outputs Connectors: One per channel, 4-position terminal strip with COM (Common), 4 ohms, 70V and 100V terminals. Accepts up to 14 AWG terminal forks. Non- touch cover included.

Output VCA Connector: 4-pinPhoenix-type connector for two VCA control lines of +10 VDC and ground. Compatible with Crown 1-VCAP and 4-VCAP modules.

Amp Config Switch: A DIP switch with two functions:

1.Assigns an input as the priority input for each output, thereby temporarily muting the remaining inputs. Muting is activated by contact closure.

2.Global enable switch for phantom power. Does not affect RCA inputs. Default position is off.

Priority Connector: 3-pin Phoenix-type connec- tor allows Input 1 or Input 5 (280MA only) to mute other input signals by contact closure.

Input Routing Switch (280MA only): DIP switches that assign each input signal to each output. Two switches per input.

Line Out Connector: One 3-pin balanced Phoe- nix-type connector per output channel. Post master, pre-VCA. Level controlled by master volume control.

The tone generator has been omitted. Call Crown Tech Support if you have a tone genera- tor question.

Input Connectors:

Mic/Line Connector: 3-pin Phoenix-type, bal- anced, one per input channel.

Dual RCA Input Connector: For stereo music signals, unbalanced, summed together, two connectors per input channel.

Amp Input Connector: 3-pin Phoenix-type, high-impedance balanced, one per amplifer channel. Used to link an additional mixer to the mixer-amplifier. Can be used to connect an external processor.

Mic/line Switch: Selects mic-level or line-level signals. One switch for each balanced input.

Link In/Out Switch: Slide switch, one per chan- nel. With the Link Switch IN, any signal applied to the Amp Input connector will be mixed with the input signal(s). With the Link Switch OUT, only the signal from the Amp Input Connector will appear at the amplifier output.

Cooling

Convection cooled.

Protection

Current Limit Protection: Included.

Thermal Limit Protection: Over-temperature thermal cutout.

DC-Fault Load Protection: Included.

Included Accessories

Power cord Detachable rack ears Screws for rack ears

Non-touch cover for output connectors Phoenix-type connectors

Spade lugs

Optional Accessories

1-VCAP remote volume control for one channel. 4-VCAP remote volume control for four chan- nels.

Dimensions

EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B) with rack ears, 3.5-inch (8.9-cm) height and 12.2-inch (31.0-cm) depth behind the mounting surface (not including non- touch cover). 4.1 inches (10.5 cm) high includ- ing feet. 13.9 inches (35.2 cm) deep from front of knobs to back of non-touch cover.

Weight

Net Weight:

180MA: 21.0 lbs. (9.5 kg).

280MA: 25.3 lbs. (11.5 kg)

1160MA: 25.3 lbs. (11.5 kg)

Shipping Weight:

180MA: 26.0 lbs. (11.8 kg)

280MA: 30.3 lbs. (13.8 kg)

1160MA: 30.3 lbs. (13.8 kg)

Regulatory Certifications

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12/07

 

 

 

 

137964-2B

COMMERCIAL AUDIO

Crown’s Commercial Audio mixer/amplifiers deliver legendary Crown quality to the commercial audio industry. These high-value mixer-amplifiers provide both 4-ohm and constant-voltage outputs (70V and 100V) for use in a wide range of commercial applications including schools, hospitals, factories, restaurant/retail, houses of worship, fitness facilities, A/V boardrooms, correctional facilities, and small offices. Easily configured for a range of uses such as paging, background music, security, and evacua-

tion instructions, Crown’s Commercial Audio units are the smart choice for commercial sound.

Page 23
Image 23
Crown CTS 600, CTS 3000 manual THD Less than 0.5% at rated power at 1 kHz, Input Sensitivity for full output at maximum gain

CTS 600, CTS 1200, CTS 2000, CTS 3000 specifications

Crown, a leading name in material handling equipment, has developed the Crown CTS series, which includes the CTS 3000, CTS 2000, CTS 600, and CTS 1200 models. Each of these rugged machines is designed to enhance productivity and efficiency in various warehouse and distribution applications, integrating innovative technologies and robust features.

The Crown CTS 3000 is the flagship model in this series, designed for high-demand environments that require exceptional lifting capability. It boasts a powerful AC drive system that offers superior acceleration and speed control, providing operators with smooth and responsive handling. The heightened visibility from the operator's compartment minimizes blind spots, enhancing safety and efficiency during operations. The CTS 3000 also features advanced battery management technology, allowing for prolonged operation and minimal downtime.

Next in line is the Crown CTS 2000, which is tailored for a range of medium-duty applications. While its lifting capacity is slightly lower than the CTS 3000, it incorporates many similar functionalities. It features a user-friendly control interface, making it easy for operators of any skill level to manage tasks efficiently. The robust design ensures reliability and durability, making it an excellent choice for businesses that require consistent performance under moderately demanding conditions.

The Crown CTS 600 model is specially designed for light-duty operations. Ideal for shorter runs and smaller spaces, the CTS 600 is compact and maneuverable without compromising on performance. It comes equipped with advanced safety features, including an integrated operator presence system that ensures safe operation. The model’s light weight also translates into better battery efficiency, making it a cost-effective option for businesses seeking to optimize their operational expenses.

Lastly, the Crown CTS 1200 is a versatile model that strikes a balance between power and agility. It is particularly suitable for environments where space is at a premium. The CTS 1200 is engineered for versatility, allowing it to handle a variety of loads with ease. It features intuitive controls and exceptional ergonomics, contributing to operator comfort during long shifts. This model also emphasizes energy efficiency and reduced environmental impact through its advanced power management system.

In summary, the Crown CTS series offers a range of models catering to varying operational needs, from high-demand environments with the CTS 3000 to the space-saving capabilities of the CTS 600. Each model is built upon a foundation of advanced technologies that promote safety, efficiency, and productivity, making them indispensable tools in today's material handling landscape.